HardLabs

Carrier board arduino current driver

gkeiel·pcb_design_kicad·arduino_nano_relay_module/carrier_board_arduino_current_driver.kicad_pcb

Carrier board arduino current driver layout, top view — open source AVR/Arduino board by gkeiel

About the Carrier board arduino current driver

Carrier board arduino current driver is an open source AVR/Arduino PCB design by gkeiel, published on GitHub under the MIT license. It is a 2-layer board measuring 61.6 × 49.8 mm, with 29 components from 19 distinct parts.

Its main chip is the Arduino_Nano_v3.x, from the AVR/Arduino family. Other key parts include the L7805, PC817 and LM358. By type, the board carries 11 resistors, 4 diodes, 3 ICs, 3 transistors, 3 connectors and 2 capacitors.

It belongs with the dev boards & breakouts, power & battery and sensors designs in this gallery.

From the project

Printed circuit boards (PCBs) designs for some electronic circuits

A repository with designs of printed circuit boards (PCBs) for electronic circuits developed with KiCad. Each project has its own folder, focused on a different and specific problem.

The following projects are available: - full-bridge DC driver Arduino Nano (carrier board) - low-side DC driver Arduino Nano (carrier board) - relay module 5 V optocoupler SMT 4 channels - relay module 5 V optocoupler SMT - power supply with linear regulator 78xx - power supply with linear regulator lm317

Carrier board arduino current driver, from the project README
From the project README

Main components on the Carrier board arduino current driver

L7805PC817LM358Arduino_Nano_v3.x

Carrier board arduino current driver bill of materials (BOM)

29 components, 19 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
L7805
U1
1
PC817
U2
1
LM358
U3
1
Arduino_Nano_v3.x
A1
2
TIP4x/ TIP12x
Q1, Q2
1
BC817
Q3
1
Conn_01x03_Pin
J1
1
Conn_01x03_Pin
J2
1
Barrel_Jack
J3
1
Relay_SPDT
K1
1
R_Potentiometer_Trim_US
RV1
3
1N4007
D1, D3, D4
1
LED
D2
1
C_Polarized
C1
1
C
C2
8
R
R1, R2, R5, R6, R7, R8, R9, R10
1
68k
R3
1
39k
R4
1
1k
R11

Carrier board arduino current driver design files

The KiCad project lives in the gkeiel/pcb_design_kicad repository on GitHub; these links point at the commit this page was built from.

Carrier board arduino current driver: common questions

What microcontroller does the Carrier board arduino current driver use?

The Carrier board arduino current driver is built around the Arduino_Nano_v3.x, from the AVR/Arduino family.

How big is the Carrier board arduino current driver?

The Carrier board arduino current driver measures 61.6 × 49.8 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Carrier board arduino current driver?

29 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Carrier board arduino current driver design files?

From the gkeiel/pcb_design_kicad repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Carrier board arduino current driver design in my own project?

Yes, under the terms of its MIT license, which gkeiel chose for the repository.

Can I test firmware for the Carrier board arduino current driver without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in pcb_design_kicad

Similar boards