Drain watcher
gravitymir·drain_watcher·hardware/drain_watcher.kicad_pcb
About the Drain watcher PCB
Drain watcher is an open source ESP32 PCB design by gravitymir, published on GitHub under the MIT license. It is a 2-layer board measuring 52 × 45.8 mm, with 48 components from 30 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N8R2, from the ESP32 family. Other key parts include the INA228AIDGSR, AP63205WU-7 and TLV75733PDBVR. By type, the board carries 13 capacitors, 12 resistors, 8 diodes, 5 connectors, 4 ICs and 2 switches.
It belongs with the iot & wireless and usb & debug tools designs in this gallery.
From the project
Логгер тока утечки автомобильного аккумулятора: ESP32-S3 и INA228 на одной плате. Питается от того же аккумулятора через понижающий преобразователь, Wi-Fi поднимает сама: история замеров смотрится с телефона или ноутбука через веб-страницу, без проводов к машине.
Логгер тока утечки автомобильного аккумулятора: ESP32-S3 и INA228 на одной плате. Питается от того же аккумулятора через понижающий преобразователь, Wi-Fi поднимает сама: история замеров смотрится с телефона или ноутбука через веб-страницу, без проводов к машине.
Шунт стоит на силовых шинах в минусе аккумулятора, основной ток по плате не идёт: она только снимает напряжение с шунта (четырёхпроводное подключение, Kelvin) и напряжение аккумулятора.
Main components on the Drain watcher
Drain watcher bill of materials (BOM)
48 components, 30 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1-N8R2 | ESP32-S3-WROOM-1 | U1 |
| 1 | INA228AIDGSR | MSOP-10_3x3mm_P0.5mm | U2 |
| 1 | AP63205WU-7 | TSOT-23-6 | U3 |
| 1 | TLV75733PDBVR | SOT-23-5 | U4 |
| 1 | AO3400A | SOT-23 | Q1 |
| 1 | C165948 USB-C | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | S4B-PH-K-S UART0 | JST_PH_S4B-PH-K_1x04_P2.00mm_Horizontal | J3 |
| 1 | S4B-PH-K-S UART1 | JST_PH_S4B-PH-K_1x04_P2.00mm_Horizontal | J4 |
| 1 | S4B-PH-K-S I2C | JST_PH_S4B-PH-K_1x04_P2.00mm_Horizontal | J5 |
| 1 | S5B-PH-K-S GPIO | JST_PH_S5B-PH-K_1x05_P2.00mm_Horizontal | J6 |
| 1 | MLT-5020 | Buzzer_MLT-5020 | BZ1 |
| 1 | ICS-43434 | InvenSense_ICS-43434-6_3.5x2.65mm | MK1 |
| 1 | C318884 BOOT | SW_Push_1P1T_XKB_TS-1187A | SW1 |
| 1 | C318884 RESET | SW_Push_1P1T_XKB_TS-1187A | SW2 |
| 1 | SMF24CA | D_SOD-123F_Bidirectional | D1 |
| 2 | SMF24A | D_SOD-123F | D2, D3 |
| 3 | B5819W | D_SOD-123 | D4, D5, D6 |
| 1 | 1N4148WS | D_SOD-323 | D7 |
| 1 | XL-2020RGBC-WS2812B | LED_XL-2020RGBC | D8 |
| 1 | 4.7UH 4.7uH | L_Sunlord_SWPA4030S | L1 |
Show 10 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 7 | 100NF 100nF | C_0603_1608Metric | C1, C2, C3, C4, C5, C6, C7 |
| 3 | 10UF 10uF | C_0805_2012Metric | C8, C9, C10 |
| 2 | 22UF 22uF | C_0805_2012Metric | C11, C12 |
| 1 | 1UF 1uF | C_0603_1608Metric | C13 |
| 2 | 10R | R_0603_1608Metric | R1, R2 |
| 4 | 4.7K 4.7k | R_0603_1608Metric | R3, R4, R5, R6 |
| 2 | 5.1K 5.1k | R_0603_1608Metric | R7, R8 |
| 1 | 10K 10k | R_1206_3216Metric | R9 |
| 2 | 10K 10k | R_0603_1608Metric | R10, R11 |
| 1 | 100K 100k | R_0603_1608Metric | R12 |
Drain watcher design files
The KiCad project lives in the gravitymir/drain_watcher repository on GitHub; these links point at the commit this page was built from.
Drain watcher: common questions
What microcontroller does the Drain watcher use?
The Drain watcher is built around the ESP32-S3-WROOM-1-N8R2, from the ESP32 family.
How big is the Drain watcher PCB?
The Drain watcher measures 52 × 45.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Drain watcher?
48 components, from 30 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Drain watcher design files?
From the gravitymir/drain_watcher repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Drain watcher design in my own project?
Yes, under the terms of its MIT license, which gravitymir chose for the repository.
Can I test firmware for the Drain watcher without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k