Amiibo-Pixl.js Kor

Gt5588·Amiibo-Pixl.js_Kor·hw/RevA/pixl.js/pixl.js.kicad_pcb

Amiibo-Pixl.js Kor PCB layout, top view — open source Nordic nRF board by Gt5588

About the Amiibo-Pixl.js Kor PCB

Amiibo-Pixl.js Kor is an open source Nordic nRF PCB design by Gt5588, published on GitHub under the GPL-2.0 license. It is a 4-layer board measuring 40 × 23 mm, with 45 components from 30 distinct parts.

Its main chip is the nRF52832-QFxx, from the Nordic nRF family. Other key parts include the SHT20, GD25Q16C and MSW. By type, the board carries 21 capacitors, 8 resistors, 4 ICs, 3 inductors, 2 crystals and 2 connectors.

From the project

https://github.com/taegu8619/pixl.js_kor

Main components on the Amiibo-Pixl.js Kor

Amiibo-Pixl.js Kor bill of materials (BOM)

45 components, 30 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
nRF52832-QFxx
U1
1
SHT20
U2
1
GD25Q16C
U3
1
MSW
U4
1
AO3400A
Q1
1
32.768K
Y1
1
32MHz
Y2
1
Conn_01x12
J1
1
Conn_01x04
J2
1
Antenna
AE1
1
Antenna_Loop
AE2
1
Battery_Cell
BT1
1
LED_Small
D1
1
15nH
L1
1
10uH
L2
1
TBD
L3
1
1uF
C1
8
0.1uF
C2, C3, C5, C6, C7, C10, C14, C16
1
4.7uF
C4
4
12pF
C8, C11, C23, C26
Show 10 more
QtyPartRefs
1
10uF
C9
1
1uF/25V
C12
1
1uF/16V
C13
2
150pF
C15, C20
2
TBD
C17, C18
2
100K
R1, R2
2
10K
R3, R5
1
0
R4
1
10
R6
2
4.7K
R7, R8

Amiibo-Pixl.js Kor design files

The KiCad project lives in the Gt5588/Amiibo-Pixl.js_Kor repository on GitHub; these links point at the commit this page was built from.

Amiibo-Pixl.js Kor: common questions

What microcontroller does the Amiibo-Pixl.js Kor use?

The Amiibo-Pixl.js Kor is built around the nRF52832-QFxx, from the Nordic nRF family.

How big is the Amiibo-Pixl.js Kor PCB?

The Amiibo-Pixl.js Kor measures 40 × 23 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Amiibo-Pixl.js Kor?

45 components, from 30 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Amiibo-Pixl.js Kor design files?

From the Gt5588/Amiibo-Pixl.js_Kor repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Amiibo-Pixl.js Kor design in my own project?

Yes, under the terms of its GPL-2.0 license, which Gt5588 chose for the repository.

Can I test firmware for the Amiibo-Pixl.js Kor without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Nordic nRF firmware against it before you order a PCB.

Similar boards