Room sensor
gustavwrisberg·room-sensor·hardware/kicad/Room-Sensor-lowcost.kicad_pcb
About the Room sensor PCB
Room sensor is an open source ESP32 PCB design by gustavwrisberg, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 43.3 × 22 mm, with 10 components from 7 distinct parts.
Its main chip is the XIAO-ESP32-C6-SMD, from the ESP32 family. Other key parts include the SHT40-N-NF and BH1750FVI-TR. By type, the board carries 4 capacitors, 3 ICs and 2 resistors.
It belongs with the sensors and iot & wireless designs in this gallery.
From the project
Low-cost ESPHome room sensor: mmWave presence (LD2410C), temperature/humidity, light. JLCPCB-assembled XIAO ESP32C6 board + 3D-printed case.
A small, low-cost Home Assistant room sensor: mmWave presence, temperature, humidity and light on one fully assembled board, in a 3D-printed case that mounts on a wall, a ceiling, a room corner or a desk foot.
Runs ESPHome, plugs in over USB-C, and is designed so the whole board can be assembled by JLCPCB with Economic PCBA: no soldering needed, you only screw the case shut.

Main components on the Room sensor
Room sensor bill of materials (BOM)
10 components, 7 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SHT40-N-NF Nyfea(徕飞) | DFN-4_L1.5-W1.5-P0.80-TL-EP | U1 |
| 1 | XIAO-ESP32-C6-SMD | XIAO-ESP32-C6-SMD | U2 |
| 1 | BH1750FVI-TR ROHM(罗姆) | WSOF-6_L2.6-W1.6-P0.50-TL-EP | U4 |
| 1 | HLK-LD2410C-P HI-LINK(海凌科) | SENSOR-TH_HLK-LD2410C-P | SM1 |
| 1 | 10 µF | C_0805_2012Metric | C7 |
| 3 | 100 nF | C_0402_1005Metric | C9, C11, C12 |
| 2 | 4k7 | R_0402_1005Metric | R8, R9 |
Room sensor design files
The KiCad project lives in the gustavwrisberg/room-sensor repository on GitHub; these links point at the commit this page was built from.
Room sensor: common questions
What microcontroller does the Room sensor use?
The Room sensor is built around the XIAO-ESP32-C6-SMD, from the ESP32 family.
How big is the Room sensor PCB?
The Room sensor measures 43.3 × 22 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Room sensor?
10 components, from 7 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Room sensor design files?
From the gustavwrisberg/room-sensor repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Room sensor design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which gustavwrisberg chose for the repository.
Can I test firmware for the Room sensor without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k