Smart Tripod

henry-thomas-1·ECE-445-Smart-Tripod·Smart Tripod/Smart Tripod.kicad_pcb

Smart Tripod PCB layout, top view — open source ESP32 board by henry-thomas-1

About the Smart Tripod PCB

Smart Tripod is an open source ESP32 PCB design by henry-thomas-1, published on GitHub under the MIT license. It is a 2-layer board measuring 99 × 62.5 mm, with 100 components from 46 distinct parts.

Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the AZ1117-3.3, TPS565201DDCR and MIC29300-5.0WU-TR. By type, the board carries 37 resistors, 26 capacitors, 25 connectors, 5 ICs, 4 switches and 2 inductors.

It belongs with the iot & wireless and robotics & motion designs in this gallery.

From the project

Smart Motorized Tripod Overview The Smart Motorized Tripod is a real-time camera tracking system designed to automate framing and subject centering. The system integrates an ESP32-S3, Raspberry Pi 4, stepper motors, and a custom PCB to control camera positioning and enable remote

Smart Motorized Tripod Overview The Smart Motorized Tripod is a real-time camera tracking system designed to automate framing and subject centering. The system integrates an ESP32-S3, Raspberry Pi 4, stepper motors, and a custom PCB to control camera positioning and enable remote operation. Key technologies include OpenCV for object tracking, AirPlay for live streaming, and WebSockets for wireless communication.

Smart Tripod, from the project README
From the project README

Main components on the Smart Tripod

Smart Tripod bill of materials (BOM)

100 components, 46 distinct parts.

QtyPartRefs
1
ESP32-S3-WROOM-1
U1
1
AZ1117-3.3
U2
2
TPS565201DDCR
U3, U4
1
MIC29300-5.0WU-TR
U5
1
PMOS
Q1
1
USB_B_Micro
J1
1
5V to Raspi
J2
1
PAN-UP
J3
1
XT30PW-M
J4
1
TILT-LEFT
J5
1
PAN-DOWN
J6
1
TILT-RIGHT
J7
1
PICTURE
J8
1
ZOOM-IN
J9
1
VIDEO
J10
1
ZOOM-OUT
J11
1
MODE
J12
1
LED-IO2
J13
1
SPEED-DOWN
J14
1
SPPED-UP
J15
Show 26 more
QtyPartRefs
1
IO3
J16
1
IO4
J17
1
IO5
J18
1
IO6
J19
1
IO7
J20
1
IO8
J21
1
IO9
J22
1
IO10
J23
2
Ground
J24, J25
1
Boot Switch
SW1
1
Enable Switch
SW2
1
USB/Battery Switch
SW3
1
Power Switch
SW4
2
3.3uH
L3, L4
4
10uF
C1, C3, C5, C9
3
22uF
C2, C8, C12
1
0.1uF
C4
4
100nF
C6, C7, C11, C22
12
1uF
C10, C13, C14, C15, C16, C17, C18, C19 +4
1
15uF
C25
1
15uF
C26
10
R
R1, R3, R26, R27, R28, R29, R30, R31 +2
2
10kOhm
R2, R4
23
10k
R5, R6, R7, R8, R9, R10, R11, R12 +15
1
100R
R24
1
5k
R25

Smart Tripod design files

The KiCad project lives in the henry-thomas-1/ECE-445-Smart-Tripod repository on GitHub; these links point at the commit this page was built from.

Smart Tripod: common questions

What microcontroller does the Smart Tripod use?

The Smart Tripod is built around the ESP32-S3-WROOM-1, from the ESP32 family.

How big is the Smart Tripod PCB?

The Smart Tripod measures 99 × 62.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Smart Tripod?

100 components, from 46 distinct parts. The full bill of materials is listed on this page.

Where can I download the Smart Tripod design files?

From the henry-thomas-1/ECE-445-Smart-Tripod repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Smart Tripod design in my own project?

Yes, under the terms of its MIT license, which henry-thomas-1 chose for the repository.

Can I test firmware for the Smart Tripod without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in ECE-445-Smart-Tripod

Similar boards