Group 29 Handheld

henry-thomas-1·ECE-445-Smart-Tripod·kicad/Group_29_Handheld/Group_29_Handheld.kicad_pcb

Group 29 Handheld PCB layout, top view — open source ESP32 board by henry-thomas-1

About the Group 29 Handheld PCB

Group 29 Handheld is an open source ESP32 PCB design by henry-thomas-1, published on GitHub under the MIT license. It is a 2-layer board measuring 89 × 65.5 mm, with 66 components from 45 distinct parts.

Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the TPS562201DDCR, TPS565201DDCR, AZ1117-3.3 and MIC29300-5.0WU-TR. By type, the board carries 21 capacitors, 15 resistors, 6 connectors, 5 ICs, 4 switches and 4 test points.

From the project

The above files are set as Handheld, however they are the files for the motorized tripod. Backups are included of the files over minor changes and major changes to the PCB.

Group 29 Handheld, from the project README
From the project README

Main components on the Group 29 Handheld

Group 29 Handheld bill of materials (BOM)

66 components, 45 distinct parts.

QtyPartRefs
1
ESP32-S3-WROOM-1
U1
1
TPS562201DDCR
U2
1
TPS565201DDCR
U3
1
AZ1117-3.3
U4
1
MIC29300-5.0WU-TR
U5
1
PMOS
Q1
1
MicroUSB
J1
1
XT30PW-M
J2
1
Servo1
J4
1
Servo2
J5
1
Extra GPIO
J7
1
LEDIO
J8
1
60
3V3_R1
1
140
5V_R1
1
260
7V5_R1
1
100
Flash_R1
1
Enable Switch
SW1
1
Boot Switch
SW2
1
On/Off
SW3
1
3v3Switch
SW4
Show 25 more
QtyPartRefs
1
+5V
TP1
1
+3.3
TP2
1
GND
TP3
1
MotorTP
TP4
4
LED
3v3LED1, 5VLED1, 7V4LED1, FlashLED1
2
IHLP3232DZER3R3M01
L2, L3
4
10uF
C1, C5, C11, C24
4
22uF
C2, C7, C22, C23
7
100nF
C3, C4, C6, C8, C9, C14, C15
3
1uF
C10, C13, C18
1
15uF
C12
2
220uF
C17, C20
3
10k
R1, R4, R6
1
100k
R2
1
R_3p1
R3
1
R_5S2
R5
1
100
R8
1
R_3p3
R13
1
R_3p2
R14
1
R_3S2
R15
1
R_3S1
R16
1
R_5P2
R17
1
R_5S1
R18
1
R_5P3
R19
1
R_5P1
R20

Group 29 Handheld design files

The KiCad project lives in the henry-thomas-1/ECE-445-Smart-Tripod repository on GitHub; these links point at the commit this page was built from.

Group 29 Handheld: common questions

What microcontroller does the Group 29 Handheld use?

The Group 29 Handheld is built around the ESP32-S3-WROOM-1, from the ESP32 family.

How big is the Group 29 Handheld PCB?

The Group 29 Handheld measures 89 × 65.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Group 29 Handheld?

66 components, from 45 distinct parts. The full bill of materials is listed on this page.

Where can I download the Group 29 Handheld design files?

From the henry-thomas-1/ECE-445-Smart-Tripod repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Group 29 Handheld design in my own project?

Yes, under the terms of its MIT license, which henry-thomas-1 chose for the repository.

Can I test firmware for the Group 29 Handheld without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in ECE-445-Smart-Tripod

Similar boards