Esp32-s3-devkit
HeyPCB·esp32-s3-devkit
About the Esp32-s3-devkit PCB
Esp32-s3-devkit is an open source ESP32 PCB design by HeyPCB, published on GitHub under the MIT license. It is a 4-layer board measuring 31 × 64 mm, with 30 components from 16 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N8R8, from the ESP32 family. Other key parts include the AMS1117-3.3 and USBLC6-2SC6. By type, the board carries 12 capacitors, 6 resistors, 4 diodes, 3 ICs, 3 connectors and 2 switches.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
ESP32-S3 dev board in the DevKitC-1 layout (31 x 64 mm, 4 layers, KiCad 10), built through HeyPCB's MCP server
A 31 × 64 mm ESP32-S3 development board laid out like Espressif's DevKitC-1: the WROOM-1 module at the top with its antenna on the edge, an 18-pin header down each side, three WS2812B LEDs, and USB-C between RST and BOOT.
An agent built it through HeyPCB's MCP server: blocks, parts, nets, hand placement, routing and checks, all as tool calls. KiCad 10 opens the files directly, and the board is on Circuit World to open or fork in HeyPCB (sign-in required).

Main components on the Esp32-s3-devkit
Esp32-s3-devkit bill of materials (BOM)
30 components, 16 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1-N8R8 | ESP32-S3-WROOM-1 | U1 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U2 |
| 1 | USBLC6-2SC6 | SOT95P280X145-6N | U3 |
| 1 | C165948 USB-C | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | C2894941 Left | PinHeader_1x18_P2.54mm_Vertical | J2 |
| 1 | C2894941 Right | PinHeader_1x18_P2.54mm_Vertical | J3 |
| 1 | C2886902 BOOT | SW_SPST_TL3305A | SW1 |
| 1 | C2886902 RST | SW_SPST_TL3305A | SW2 |
| 3 | WS2812B | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1, D2, D3 |
| 1 | 1N5819W | D_SOD-123 | D4 |
| 3 | 100NF 100nF | C_0603_1608Metric | C1, C6, C7 |
| 6 | 10UF 10uF | C_0805_2012Metric | C2, C3, C4, C5, C11, C12 |
| 3 | 100NF 100nF | C_0402_1005Metric | C8, C9, C10 |
| 3 | 10K 10k | R_0603_1608Metric | R1, R4, R5 |
| 2 | 5.1K 5.1k | R_0402_1005Metric | R2, R3 |
| 1 | 330 | R_0402_1005Metric | R6 |
Esp32-s3-devkit design files
The KiCad project lives in the HeyPCB/esp32-s3-devkit repository on GitHub; these links point at the commit this page was built from.
Esp32-s3-devkit: common questions
What microcontroller does the Esp32-s3-devkit use?
The Esp32-s3-devkit is built around the ESP32-S3-WROOM-1-N8R8, from the ESP32 family.
How big is the Esp32-s3-devkit PCB?
The Esp32-s3-devkit measures 31 × 64 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Esp32-s3-devkit?
30 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Esp32-s3-devkit design files?
From the HeyPCB/esp32-s3-devkit repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Esp32-s3-devkit design in my own project?
Yes, under the terms of its MIT license, which HeyPCB chose for the repository.
Can I test firmware for the Esp32-s3-devkit without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k