Esp32 ina226
HeyPCB·esp32-sensors-2·boards/ina226/kicad/esp32_ina226.kicad_pcb
About the Esp32 ina226 PCB
Esp32 ina226 is an open source ESP32 PCB design by HeyPCB, published on GitHub under the CERN-OHL-S-2.0 license. It is a 4-layer board measuring 30 × 60 mm, with 26 components from 21 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the USBLC6-2SC6, AP2112K-3.3TRG1 and INA226AIDGSR. By type, the board carries 9 resistors, 7 capacitors, 4 ICs, 2 connectors, 2 switches and 2 diodes.
It belongs with the sensors and iot & wireless designs in this gallery.
From the project
ESP32-S3 boards, one sensor each: KiCad 10, JLCPCB-ready, CERN-OHL-S-2.0
An ESP32-S3 board with TI INA226 load current, voltage and power monitor: USB-C, Wi-Fi and Bluetooth LE, ready to flash.
Not fabricated, assembled or powered. Every number on this page is measured by KiCad 10 on the files in this folder; the full measurements are in report.json.
A small ESP32-S3 development board built around one sensor: TI INA226 load current, voltage and power monitor. Plug in USB-C, flash it from Arduino, ESP-IDF or MicroPython over the ESP32-S3's native USB, and read the sensor. One of the HeyPCB ESP32 sensor series: the same ESP32-S3 template with a different sensor on…

Main components on the Esp32 ina226
Esp32 ina226 bill of materials (BOM)
26 components, 21 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | USBLC6-2SC6 | SOT-23-6 | U1 |
| 1 | AP2112K-3.3TRG1 AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | ESP32-S3-WROOM-1-N16R8 | ESP32-S3-WROOM-1 | U3 |
| 1 | INA226AIDGSR | TSSOP-10_3x3mm_P0.5mm | U4 |
| 1 | TYPE-C-31-M-12 USB-C | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | MX126-5.0-03P-GN01-Cu-S-A IN OUT GND | TerminalBlock_MaiXu_MX126-5.0-03P_1x03_P5.00mm | J2 |
| 1 | TS-1187A-B-A-B BOOT | SW_Push_1P1T_XKB_TS-1187A | SW1 |
| 1 | TS-1187A-B-A-B RESET | SW_Push_1P1T_XKB_TS-1187A | SW2 |
| 1 | NCD0603B1 Blue (IO48) | LED_0603_1608Metric | D1 |
| 1 | KT-0603G Green (PWR) | LED_0603_1608Metric | D2 |
| 1 | CL21A106KAYNNNE 10uF | C_0805_2012Metric | C1 |
| 3 | CL10A105KB8NNNC 1uF | C_0603_1608Metric | C2, C3, C6 |
| 1 | CC0603KRX7R9BB104 100nF | C_0603_1608Metric | C4 |
| 1 | CL21A226MAQNNNE 22uF | C_0805_2012Metric | C5 |
| 1 | CL05B104KO5NNNC 100nF | C_0402_1005Metric | C7 |
| 2 | 0402WGF5101TCE 5.1k | R_0402_1005Metric | R1, R2 |
| 2 | 0603WAF1002T5E 10k | R_0603_1608Metric | R3, R6 |
| 1 | 0603WAF1001T5E 1k | R_0603_1608Metric | R4 |
| 1 | 0603WAF2201T5E 2.2k | R_0603_1608Metric | R5 |
| 1 | FMF06FTHR010-LH 10m | R_1206_3216Metric | R7 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 0603WAF4701T5E 4.7k | R_0603_1608Metric | R8, R9 |
Esp32 ina226 design files
The KiCad project lives in the HeyPCB/esp32-sensors-2 repository on GitHub; these links point at the commit this page was built from.
Esp32 ina226: common questions
What microcontroller does the Esp32 ina226 use?
The Esp32 ina226 is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.
How big is the Esp32 ina226 PCB?
The Esp32 ina226 measures 30 × 60 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Esp32 ina226?
26 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Esp32 ina226 design files?
From the HeyPCB/esp32-sensors-2 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Esp32 ina226 design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which HeyPCB chose for the repository.
Can I test firmware for the Esp32 ina226 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in esp32-sensors-2
ESP32
Esp32 mpr121
HeyPCB
30 × 48 mm27 parts4LCERN-OHL-S-2.00ESP32
Esp32 bno055
HeyPCB
30 × 48 mm27 parts4LCERN-OHL-S-2.00ESP32
Esp32 ina237
HeyPCB
30 × 60 mm26 parts4LCERN-OHL-S-2.00ESP32
Esp32 ina238
HeyPCB
30 × 60 mm26 parts4LCERN-OHL-S-2.00ESP32
Esp32 ina233
HeyPCB
30 × 60 mm26 parts4LCERN-OHL-S-2.00ESP32
Esp32 vl53l1x
HeyPCB
30 × 48 mm25 parts4LCERN-OHL-S-2.00ESP32
Esp32 icm20602
HeyPCB
30 × 48 mm25 parts4LCERN-OHL-S-2.00ESP32
Esp32 lis3mdl
HeyPCB
30 × 48 mm25 parts4LCERN-OHL-S-2.00ESP32
Esp32 ads1115
HeyPCB
30 × 48 mm25 parts4LCERN-OHL-S-2.00ESP32
Esp32 icm20948
HeyPCB
30 × 48 mm25 parts4LCERN-OHL-S-2.00ESP32
Esp32 lis3dh
HeyPCB
30 × 48 mm25 parts4LCERN-OHL-S-2.00
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k