64 open source boards using the INA226AIDGSR
Real designs built with the INA226AIDGSR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Moss
metrox-eth
82 × 79 mm208 parts4LApache-2.0116USB-C PD 5V supply — development
rjwalters
100 × 65 mm47 parts4LMIT74PIC
Aper-Oculus
ApotheoTech
147.4 × 90 mm557 parts16LGPL-3.032ESP32
CloudSmoker
cwgstreet
70 × 70 mm56 parts4LMIT24ESP32
Fugu2
fl4p
50 × 88 mm100 parts2LNo license21STM32
PowerWatch
zhbi98
86 × 45 mm61 parts2LMIT15STM32
Oro Link
oro-os
153.7 × 88.9 mm341 parts8LMIT13AVR/Arduino
Power board v1
misko
100 × 65 mm133 parts4LNo license12STM32
Main
HelloAlex4
115 × 82.3 mm249 parts4LCC-BY-NC-4.010STM32
TET-Module
ICDT-Inatel-Cubesat-Design-Team
90.2 × 95.9 mm76 parts4LCERN-OHL-W-2.05Opsum
nitefood
80 × 50 mm41 parts2LMIT5ESP32
LIONv3-R
RodrigoCAndrade
50.2 × 85.2 mm79 parts4LNo license4Pre route
ramalamadingdong
53.3 × 68.6 mm49 parts4LGPL-3.04AVR/Arduino
MPPT
aati106
90.4 × 69.6 mm93 parts2LNo license2ESP32
LIONv3-Mini
RodrigoCAndrade
50.2 × 40.2 mm78 parts4LNo license2- schematic only · 139 partsESP32
GrowHub
Ajakovski
139 partsMIT2 STM32
Rabbit 2.0 body board (deck 2)
seralexeev
120.5 × 269.9 mm323 parts4LNo license1RP2040/RP2350
Spark
ratmuds
82 × 55 mm196 parts4LNo license1RP2040/RP2350
Tool power supply
UBC-Hacker-Fab
90 × 160 mm121 parts4LNo license1STM32
Flyback-Driver
Operationorange01
128 × 72.5 mm115 parts4LNo license1STM32
MPPT Solar KiCAD Rev2.1
wilhelmzeuschner
80 × 65 mm107 parts4LMIT1PVDX-ADCS-PMB
BrownSpaceEngineering
82.5 × 82.5 mm106 parts4LNo license1RP2040/RP2350
Odock
KarpelesLab
130 × 89 mm772 parts6LCERN-OHL-P-2.00RP2040/RP2350
Odeck
KarpelesLab
130 × 89 mm772 parts6LCERN-OHL-P-2.00ESP32
CanSat
budabalint
54 × 52 mm439 parts4LNo license0PIC
LPS
OberTechniks
120 × 149.5 mm251 parts2LNo license0STM32
EPS
MatthiasGeorgImhof
80 × 80 mm238 parts4LCC-BY-NC-4.00Ito controller
luciddreams
160 × 110 mm202 parts4LNo license0ESP32
PCB EU
nikolajevs
100 × 100 mm188 parts4LNo license0Quack core
HeyPCB
101 × 51.5 mm126 parts4LCERN-OHL-S-2.00ESP32
Gopo
gokcesena53
99.4 × 61 mm125 parts4LMIT0STM32
CANSAT ARLISS STM32
JosephPalacios-so
90 × 75 mm110 parts4LNo license0NavPoTS-South
RuberDuck9
58.9 × 58.9 mm106 parts4LAGPL-3.00RP2040/RP2350
EWP-Control
haum2002
76 × 64 mm93 parts4LNo license0ZU64DR RFSOC
hamedroghani
200 × 150 mm87 parts12LNo license0Iris brainstem
HeyPCB
64 × 80 mm85 parts4LCERN-OHL-S-2.00
How designs wire the INA226AIDGSR
Read from the KiCad layouts of 50 open source designs, one per repository: what each pin of the INA226AIDGSR connects to, and the resistors, capacitors and other passives placed on it.
- The VS_6 pin has a decoupling capacitor on 40 of 50 designs, most often 100 nF (then 10 µF).
- The A1_1 pin is tied to GND on 41 of 50 designs (3.3V on 3, a signal on 5).
- The A0_2 pin is tied to GND on 41 of 50 designs (a signal on 8).
- The SDA_4 pin has a pull-up to 3.3V on 33 of 50 designs, most often 4.7 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| A1_1pin 1 | Connected to: GND 82% | — |
| A0_2pin 2 | Connected to: GND 82% · a signal 16% | — |
| ALERT_3pin 3 | Connected to: The microcontroller 26%, a connector 20% · not connected 38% |
|
| SDA_4pin 4 | Connected to: The microcontroller 50%, a connector 30% |
|
| SCL_5pin 5 | Connected to: The microcontroller 50%, a connector 32% |
|
| VS_6pin 6 | Connected to: 3.3V 90% |
|
| GND_7pin 7 | Connected to: GND 92% | — |
| VBUS_8pin 8 | Connected to: Signal 56% · 3.3V 44% |
|
| VIN+_10pin 10 | Connected to: Signal 60% · 3.3V 34% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Moss by metrox-eth, USB-C PD 5V supply — development by rjwalters, Aper-Oculus by ApotheoTech and 1u panel by oresat.
The INA226AIDGSR in open source designs
The gallery holds 64 open source boards using the INA226AIDGSR from 53 GitHub repositories; a typical one measures about 80 × 69.6 mm and carries around 93 components.
66% use four copper layers or more, and 38% carry an open source license.
The most starred is Moss by metrox-eth.
Parts used alongside the INA226AIDGSR
Microcontrollers on boards using the INA226AIDGSR
What boards using the INA226AIDGSR are built for
INA226AIDGSR: common questions
Where can I find a INA226AIDGSR reference design?
Each of the 64 boards on this page is a real design using the INA226AIDGSR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the INA226AIDGSR VS_6 pin?
The VS_6 pin has a decoupling capacitor on 40 of 50 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 50 open source designs using the INA226AIDGSR.
How is the INA226AIDGSR A1_1 pin connected?
The A1_1 pin is tied to GND on 41 of 50 designs (3.3V on 3, a signal on 5). Counted from the KiCad layouts of 50 open source designs using the INA226AIDGSR.
How is the INA226AIDGSR A0_2 pin connected?
The A0_2 pin is tied to GND on 41 of 50 designs (a signal on 8). Counted from the KiCad layouts of 50 open source designs using the INA226AIDGSR.
What parts are used alongside the INA226AIDGSR?
The USBLC6-2SC6, AP2112K-3.3TRG1, ADS1115IDGSR, LM74800QDRRRQ1 and AP63203WU-7 appear in the most repositories here.
Which microcontrollers do boards using the INA226AIDGSR use?
Most are built on ESP32 (15), STM32 (14), RP2040/RP2350 (7) and AVR/Arduino (3).
How big is a typical board using the INA226AIDGSR?
The median is 80 × 69.6 mm, and 34% are two-layer designs.
What is the most popular open source board using the INA226AIDGSR?
By GitHub stars, Moss by metrox-eth, with 116 stars.
Can I simulate one of these boards using the INA226AIDGSR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.