Kestrel fc

HeyPCB·kestrel-fc·kicad/kestrel_fc.kicad_pcb

Kestrel fc PCB layout, top view — open source STM32 board by HeyPCB

About the Kestrel fc PCB

Kestrel fc is an open source STM32 PCB design by HeyPCB, published on GitHub under the CERN-OHL-S-2.0 license. It is a 6-layer board measuring 40 × 40 mm, with 93 components from 41 distinct parts.

Its main chip is the STM32H743VIT6, from the STM32 family. Other key parts include the ICM-20602, BMI088, MS561101BA03-50, W25Q128JVSIQ and LMR51430YFDDCR. By type, the board carries 39 capacitors, 28 resistors, 10 ICs, 5 connectors, 5 diodes and 2 transistors.

It belongs with the robotics & motion designs in this gallery.

From the project

Kestrel H7: STM32H743 FPV flight controller with ICM-20602 + BMI088, MS5611, 16 MB blackbox, 5 V and switchable 10 V BECs. 40 x 40 mm 6-layer KiCad 10 board, DRC clean, with gerbers, BOM, CPL, STEP and a Betaflight target.

An STM32H743 flight controller for 5-inch 6S quads: two IMUs, a barometer, a 16 MB blackbox and its own 5 V and switchable 10 V BECs, on a 30.5 mm stack.

The Kestrel H7 is the flight controller of Kestrel, a 5-inch 6S FPV quad's electronics. Its pin map follows Betaflight's MATEKH743 target wherever the functions match, so its timer and DMA assignments are proven ones; a Betaflight unified target and CLI defaults are in firmware/. The ICM-20602 flies Betaflight, and the BMI088 on its own SPI bus is there for INAV and ArduPilot.

Kestrel fc, from the project README
From the project README

Main components on the Kestrel fc

Kestrel fc bill of materials (BOM)

93 components, 41 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
STM32H743VIT6
U1
1
ICM-20602
U2
1
BMI088
U3
1
MS561101BA03-50
MS5611
U4
1
W25Q128JVSIQ
U5
2
LMR51430YFDDCR
LMR51430YF
U6, U7
2
AP2112K-3.3TRG1
AP2112K-3.3
U8, U9
1
USBLC6-2SC6
U10
2
AO3400A
Q1, Q2
1
TAXM8M4RDBCCT2T
8MHz
Y1
1
SM08B-SRSS-TB(LF)(SN)
ESC
J1
1
SM06B-SRSS-TB(LF)(SN)
VTX
J2
1
SM04B-SRSS-TB(LF)(SN)
RX
J3
1
SM06B-SRSS-TB(LF)(SN)
GPS
J4
1
HC-TYPE-C-16P-01A
USB-C
J5
1
B3U-1000P
BOOT
SW1
1
SMAJ30A
D1
1
B5819W SL
B5819W
D2
1
NCD0603B1
Blue
D3
1
KT-0603G
Green
D4
Show 21 more
QtyPartRefs
1
KT-0603R
Red
D5
1
SWPA5040S3R3MT
3.3uH
L1
1
SWPA5040S6R8MT
6.8uH
L2
18
CL05B104KO5NNNC
100nF
C1, C2, C3, C4, C5, C10, C11, C14 +10
1
CL10A475KO8NNNC
4.7uF
C6
2
CL05A225MQ5NSNC
2.2uF
C7, C8
5
CL05A105KA5NQNC
1uF
C9, C35, C36, C37, C38
2
CL10C120JB8NNNC
12pF
C12, C13
8
GRM21BR61H106KE43L
10uF
C21, C24, C27, C28, C29, C32, C33, C34
2
CL05B104KB54PNC
100nF
C25, C30
1
CL21A106KAYNNNE
10uF
C39
6
0402WGF1002TCE
10k
R1, R2, R7, R8, R9, R10
3
0402WGF330JTCE
33
R3, R4, R28
2
0402WGF2201TCE
2.2k
R5, R6
2
0402WGF1001TCE
1k
R11, R12
6
0603WAF1003T5E
100k
R13, R15, R16, R18, R19, R24
1
0603WAF1372T5E
13.7k
R14
1
0603WAF6491T5E
6.49k
R17
2
0402WGF1003TCE
100k
R20, R21
2
0402WGF5101TCE
5.1k
R22, R23
3
0603WAF1001T5E
1k
R25, R26, R27

Kestrel fc design files

The KiCad project lives in the HeyPCB/kestrel-fc repository on GitHub; these links point at the commit this page was built from.

Kestrel fc: common questions

What microcontroller does the Kestrel fc use?

The Kestrel fc is built around the STM32H743VIT6, from the STM32 family.

How big is the Kestrel fc PCB?

The Kestrel fc measures 40 × 40 mm, has 6 copper layers and is 1.6 mm thick.

How many components are on the Kestrel fc?

93 components, from 41 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Kestrel fc design files?

From the HeyPCB/kestrel-fc repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Kestrel fc design in my own project?

Yes, under the terms of its CERN-OHL-S-2.0 license, which HeyPCB chose for the repository.

Can I test firmware for the Kestrel fc without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards