Placa controlador lumen
HiroLifeCreative·placa-controlador-lumen
About the Placa controlador lumen PCB
Placa controlador lumen is an open source ESP32 PCB design by HiroLifeCreative, published on GitHub. It is a 2-layer board measuring 100 × 70 mm, with 45 components from 14 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N8R8, from the ESP32 family. Other key parts include the MP2315S, TPS563201 and MAX3485. By type, the board carries 9 ICs, 5 connectors, 4 resistors, 2 inductors and 1 fuse.
From the project
Lumen by AxionOS rear controller board v1.0: ESP32-S3, RS-485, 4x DMX underglow. Schematic + placement, unrouted, not fabricable.
Controller board for the Lumen by AxionOS rear system (BMW 330i G20): ESP32-S3 + RS-485 (emblem + CM5) + 4x DMX underglow universes + 12 V power.
STATUS: schematic + placement v1.0, UNROUTED. NOT FABRICABLE. - No tracks in the PCB file yet. - The U1 (ESP32-S3-WROOM-1) footprint in v1.0 is WRONG (2 straight rows of 20 pads). The correct footprint per Espressif Fig. 10 is U-shaped: pads 1-15 on one side, 16-25 on the bottom edge, 26-40 on the other side, with the 18 x 6 mm antenna area on top. Redraw U1 before routing. - See lumen-controlador-placa.FICHA.md (Spanish datasheet) for blocks…
Main components on the Placa controlador lumen
Placa controlador lumen bill of materials (BOM)
45 components, 14 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1-N8R8 | ESP32-S3-WROOM-1 | U1 |
| 1 | MP2315S | TSOT23-8 | U2 |
| 1 | TPS563201 | SOT-23-6 | U3 |
| 6 | MAX3485 | SOP-8 | U4, U5, U6, U7, U8, U9 |
| 5 | Micro-Fit 4p 43045 | MF-4P | J-CM5, J-UG1, J-UG2, J-UG3, J-UG4 |
| 18 | PENDIENTE | PASIVO | C_BST3, C_IN_12V, C_OUT_3V3, C_OUT_5V, C_T4, C_T5, C_T6, C_T7 +10 |
| 2 | TVS (PENDIENTE) | TVS | D_CM5_A, D_CM5_B |
| 1 | Fusible 10A | FUSE | F1 |
| 4 | PTC 3A (PENDIENTE) | PTC | PTC1, PTC2, PTC3, PTC4 |
| 2 | Inductor (PENDIENTE) | IND | L1, L2 |
| 1 | 33 k (calculado) | PASIVO | R1_3V3 |
| 1 | 40,2 k | PASIVO | R1_5V |
| 1 | 10 k (calculado) | PASIVO | R2_3V3 |
| 1 | 7,5 k | PASIVO | R2_5V |
Placa controlador lumen design files
The KiCad project lives in the HiroLifeCreative/placa-controlador-lumen repository on GitHub; these links point at the commit this page was built from.
Placa controlador lumen: common questions
What microcontroller does the Placa controlador lumen use?
The Placa controlador lumen is built around the ESP32-S3-WROOM-1-N8R8, from the ESP32 family.
How big is the Placa controlador lumen PCB?
The Placa controlador lumen measures 100 × 70 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Placa controlador lumen?
45 components, from 14 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Placa controlador lumen design files?
From the HiroLifeCreative/placa-controlador-lumen repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Placa controlador lumen design in my own project?
The repository has no license, so all rights stay with HiroLifeCreative. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Placa controlador lumen without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k