77 open source boards using the MAX3485
Real designs built with the MAX3485, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Stack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kSTM32
Explorer
anyshake
100 × 100 mm244 parts2LCustom license98Rx72t 100 pga usb
hirakuni45
120 × 80 mm109 parts2LBSD-3-Clause86ESP32
OpenAirScope
emertcakir
100 × 75 mm247 parts4LMIT26STM32
Main
wgbowley
60 × 40 mm59 parts2LMIT10ESP32
Rs485-spy injector
rmingon
92 × 51 mm44 parts2LCERN-OHL-S-2.06ESP32
Esp32-modbus serial adapter
tomasmcguinness
27.9 × 41.7 mm22 parts2LNo license4ESP8266
SHMod24
LeoDJ
49.5 × 49.5 mm64 parts2LMIT3ESP32
PGR
Projeto-Guarda-Rios
67.5 × 44.4 mm75 parts4LMIT2STM32
Mother Ctrl
Tomoshibi-technology
100 × 60 mm248 parts2LMIT1RP2040/RP2350
DMXion 4port node
NEOgHacking
100 × 100 mm195 parts4LGPL-3.01ESP32
Iguana
iowlabs
80 × 50 mm112 parts2LNo license1STM32
NPK Board
collins-emasi
107.6 × 41 mm104 parts4LNo license1ESP32
Soil metrics
Aryan-git-byte
88.3 × 112.3 mm74 parts4LMIT1STM32
SCLF Gripper
Tknika-SCLF
67.4 × 67.4 mm70 parts4LNo license1STM32
RasPi
Tomoshibi-technology
90 × 57 mm270 parts4LNo license0ESP32
Ekspander 100x i2c
kanaboid
500 × 108.8 mm264 parts4LNo license0ESP32
IOT-project
datnguyenhcmut
100 × 75 mm247 parts4LMIT0ESP32
ESP32
Tomoshibi-technology
150 × 150 mm224 parts2LMIT0Gnu plussydisplay
gitGNU
100 × 100 mm223 parts2LGPL-3.00Ganglia
H2O-Tnp
87 × 70 mm200 parts4LNo license0CoreLight
llextv
170.7 × 119 mm192 parts4LNo license0STM32
Controladora Semaforos-2
dieleoz
156.5 × 120 mm177 parts2LNo license0STM32
H723zgt6
shydql
73.9 × 63.8 mm124 parts4LGPL-3.00RP2040/RP2350
TMC-LZ210-Command-Station
tmc-digiboys
180 × 90 mm110 parts2LCERN-OHL-P-2.00ESP32
2026 higaeri
old-bridge
111.5 × 94.5 mm89 parts2LNo license0ESP32
ES-Autologger
serhaturtis
67.3 × 85.7 mm78 parts2LNo license0ESP32
Pre-26thDenso
old-bridge
98.8 × 94 mm69 parts2LNo license0ESP32
Smart IoT Gateway Processor
Umer-Haseeb
67.7 × 71.9 mm66 parts4LNo license0Mate net monitor
ihartwig
74.7 × 51.4 mm64 parts2LMIT0AVR/Arduino
Remote unit
danielmcmillan
94 × 56.3 mm47 parts2LMIT0ESP32
Placa controlador lumen
HiroLifeCreative
100 × 70 mm45 parts2LNo license0ESP32
Firedamp fd1
saikoushiknalubola
110 × 80 mm44 parts2LNo license0ESP32
Board Production 1
Tony4tuna
116.3 × 104 mm38 parts2LNo license0ESP32
LeTube
llextv
83.1 × 34.9 mm34 parts2LNo license0Stackchan diy guide
HeliosH
50 × 50 mm33 parts2LApache-2.00
How designs wire the MAX3485
Read from the KiCad layouts of 47 open source designs, one per repository: what each pin of the MAX3485 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 31 of 47 designs, most often 100 nF (then 4.7 µF).
- The A pin has a series resistor on 28 of 47 designs, most often 120 Ω (then 0 Ω).
- The B pin has a series resistor on 28 of 47 designs, most often 120 Ω (then 10 Ω).
- The B pin has a resistor to GND on 19 of 47 designs, most often 2.2 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 5 | Connected to: GND 96% | — |
| Apin 6 | Connected to: A connector 89% |
|
| Bpin 7 | Connected to: A connector 89% |
|
| VCCpin 8 | Connected to: 3.3V 91% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Stack chan by stack-chan, Explorer by anyshake, Rx72t 100 pga usb by hirakuni45 and OpenAirScope by emertcakir.
The MAX3485 in open source designs
The gallery holds 77 open source boards using the MAX3485 from 48 GitHub repositories; a typical one measures about 90 × 61 mm and carries around 75 components.
70% are two-layer designs, the rest use four layers or more, and 58% carry an open source license.
The most starred is Stack chan by stack-chan.
Parts used alongside the MAX3485
Microcontrollers on boards using the MAX3485
What boards using the MAX3485 are built for
MAX3485: common questions
Where can I find a MAX3485 reference design?
Each of the 77 boards on this page is a real design using the MAX3485. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MAX3485 VCC pin?
The VCC pin has a decoupling capacitor on 31 of 47 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 47 open source designs using the MAX3485.
What resistor goes on the MAX3485 A pin?
The A pin has a series resistor on 28 of 47 designs, most often 120 Ω (then 0 Ω). Counted from the KiCad layouts of 47 open source designs using the MAX3485.
What resistor goes on the MAX3485 B pin?
The B pin has a series resistor on 28 of 47 designs, most often 120 Ω (then 10 Ω). Counted from the KiCad layouts of 47 open source designs using the MAX3485.
What parts are used alongside the MAX3485?
The AMS1117-3.3, AP2112K-3.3, USBLC6-2SC6, CH340K and ESP32-WROOM-32 appear in the most repositories here.
Which microcontrollers do boards using the MAX3485 use?
Most are built on STM32 (28), ESP32 (25), RP2040/RP2350 (3) and Raspberry Pi (2).
How big is a typical board using the MAX3485?
The median is 90 × 61 mm, and 70% are two-layer designs.
What is the most popular open source board using the MAX3485?
By GitHub stars, Stack chan by stack-chan, with 1,741 stars.
Can I simulate one of these boards using the MAX3485 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.