EEW-display
hnz1102·EEW-display·hw/EEW-display.kicad_pcb
About the EEW-display PCB
EEW-display is an open source ESP32 PCB design by hnz1102, published on GitHub. It is a 2-layer board measuring 139 × 64 mm, with 43 components from 32 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the MCP73831T-2ATI/OT, SPX3819M5-L, MAX98357A and ILI9488 MCU I8080 8/16BIT 3/4. By type, the board carries 13 resistors, 11 capacitors, 5 ICs, 5 switches, 3 diodes and 2 connectors.
It belongs with the iot & wireless, audio and displays & leds designs in this gallery.
From the project
ESP32-S3 firmware for a small earthquake-information display. It shows recent earthquakes and emergency earthquake warnings (緊急地震速報, EEW) from [P2P地震情報](https://www.p2pquake.net/), draws the epicenters on a Google map, and serves the same data (plus configuration) over Wi-Fi to a browser.
ESP32-S3 firmware for a small earthquake-information display. It shows recent earthquakes and emergency earthquake warnings (緊急地震速報, EEW) from P2P地震情報, draws the epicenters on a Google map, and serves the same data (plus configuration) over Wi-Fi to a browser. The display is a 480×320 ILI9488 SPI TFT in landscape orientation; a MAX98357A amplifier with an on-board speaker speaks EEWs and new earthquakes in Japanese. Written in Rust (esp-idf-hal / esp-idf-svc). The KiCad design of the board is in hw/ and a 3D-printable enclosure in STL/ (see Hardware).

Main components on the EEW-display
EEW-display bill of materials (BOM)
43 components, 32 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1-N16R8 | ESP32-S3-WROOM-1_EXP | U1 |
| 1 | MCP73831T-2ATI/OT | SOT-23-5 | U2 |
| 1 | SPX3819M5-L | SOT-23-5 | U3 |
| 1 | MAX98357A | TQFN-16-1EP_3x3mm_P0.5mm_EP1.23x1.23mm | U4 |
| 1 | ILI9488 MCU I8080 8/16BIT 3/4 | ILI9488 MCU I8080 | U5 |
| 1 | SSM3J332R | SOT-23 | Q1 |
| 1 | 32.7680KHZ 32.7680KHz | Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | USB4105-GF-A | USB_C_5077CR-16-SMC2-BK-TR | J1 |
| 1 | B2B-PH-K-S | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J2 |
| 1 | SPEAKER_UM1515IA Speaker_UM1515IA | Speaker_UM1515IA | LS1 |
| 1 | PAGE/BOOT | SW_PUSH_6mm_H8mm | SW1 |
| 1 | ZOOM-IN | SW_PUSH_6mm_H8mm | SW2 |
| 1 | MODE | SW_PUSH_6mm_H8mm | SW3 |
| 1 | ZOOM-OUT | SW_PUSH_6mm_H8mm | SW4 |
| 1 | SLIDE_SW | SLIDE_SW_IS1235-G | SW5 |
| 1 | LED RED | LED_0603_1608Metric | D1 |
| 1 | LED GREEN | LED_0603_1608Metric | D2 |
| 1 | CUS10F30 | D_SOD-323 | D3 |
| 1 | MH2029-601Y | L_0805_2012Metric | FB1 |
| 2 | 1UF 1uF | C_0805_2012Metric | C1, C10 |
Show 12 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 16PF 16pF | C_0603_1608Metric | C2, C3 |
| 4 | 0.1UF 0.1uF | C_0603_1608Metric | C4, C5, C8, C11 |
| 2 | 10UF 10uF | C_0805_2012Metric | C6, C9 |
| 1 | 4.7UF 4.7uF | C_0805_2012Metric | C7 |
| 3 | 20K 1% | R_0603_1608Metric | R1, R2, R7 |
| 1 | 10K | R_0603_1608Metric | R3 |
| 2 | 5.1K | R_0603_1608Metric | R4, R5 |
| 1 | 2K | R_0603_1608Metric | R6 |
| 1 | 12K 1% | R_0603_1608Metric | R8 |
| 2 | 330 | R_0603_1608Metric | R9, R10 |
| 1 | 100K | R_0603_1608Metric | R11 |
| 2 | 100K/0 | R_0603_1608Metric | R12, R13 |
EEW-display design files
The KiCad project lives in the hnz1102/EEW-display repository on GitHub; these links point at the commit this page was built from.
- Layouthw/EEW-display.kicad_pcb
- Schematichw/EEW-display.kicad_sch
- BOMhw/BOM.csv
EEW-display: common questions
What microcontroller does the EEW-display use?
The EEW-display is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.
How big is the EEW-display PCB?
The EEW-display measures 139 × 64 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the EEW-display?
43 components, from 32 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the EEW-display design files?
From the hnz1102/EEW-display repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the EEW-display design in my own project?
The repository has no license, so all rights stay with hnz1102. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the EEW-display without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k