GNSS-viewwer

hnz1102·GNSS-viewwer·hw/GNSS-satellite-viewer.kicad_pcb

GNSS-viewwer PCB layout, top view — open source ESP32 board by hnz1102

About the GNSS-viewwer PCB

GNSS-viewwer is an open source ESP32 PCB design by hnz1102, published on GitHub. It is a 4-layer board measuring 100 × 50.1 mm, with 68 components from 40 distinct parts.

Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the ST7789V_TFT_DISPLAY_8P, FEMC064G-M11, MAX-F10S-00B, SPX3819M5-L and MCP73831T-2ATI/OT. By type, the board carries 24 resistors, 18 capacitors, 6 ICs, 5 switches, 4 connectors and 4 diodes.

It belongs with the rf & radio, iot & wireless and power & battery designs in this gallery.

From the project

GNNS Satellite Viewer

ESP32-S3 firmware for a handheld GNSS receiver display built around a u-blox MAX-F10S module. It decodes the receiver's NMEA output and shows the fix, satellite constellation, a live map and recorded tracks on a 320×240 colour TFT, and serves the same data over Wi-Fi to a browser. Written in Rust (esp-idf-hal / esp-idf-svc) with a C component (wolfSSH) for an SSH console to the receiver.

GNSS-viewwer, from the project README
From the project README

Main components on the GNSS-viewwer

GNSS-viewwer bill of materials (BOM)

68 components, 40 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-S3-WROOM-1-N16R8
U1
1
ST7789V_TFT_DISPLAY_8P
U2
1
FEMC064G-M11
EM64VSUKN-BA000-2
U3
1
MAX-F10S-00B
U4
1
SPX3819M5-L
U5
1
MCP73831T-2ATI/OT
MCP73831-2-OT
U6
1
2N7002K
Q1
1
SSM6L56FE_LM
Q2
1
SSM3J332R
Q3
1
32.7680KHZ
32.7680KHz
Y1
2
U.FL-R-SMT-1
Conn_Coaxial
J1, J2
1
USB4105-GF-A
J3
1
B2B-PH-K-S
LiPo BATTERY
J4
1
PAGE/BOOT
SW1
1
ZOOM-IN
SW2
1
MODE
SW3
1
ZOOM-OUT
SW4
1
SLIDE_SW
SW5
1
LED BLUE
D1
1
CUS10F30
D2
Show 20 more
QtyPartRefs
1
LED RED
D3
1
LED GREEN
D4
2
MH2029-601Y
FB1, FB2
1
47NH
47nH
L1
2
16PF
16pF
C1, C3
9
0.1UF
0.1uF
C2, C4, C5, C6, C7, C8, C11, C13 +1
3
1UF
1uF
C9, C10, C18
1
10NF
10nF
C12
2
10UF
10uF
C14, C17
1
4.7UF
4.7uF
C16
3
20K 1%
R1, R2, R20
6
10K
R3, R4, R5, R8, R9, R12
4
1K
R6, R7, R10, R11
3
330
R13, R23, R24
2
100K
R14, R22
1
10 1/4W
R15
1
49.9
R16
2
5.1K
R17, R18
1
2K
R19
1
12K 1%
R21

GNSS-viewwer design files

The KiCad project lives in the hnz1102/GNSS-viewwer repository on GitHub; these links point at the commit this page was built from.

GNSS-viewwer: common questions

What microcontroller does the GNSS-viewwer use?

The GNSS-viewwer is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.

How big is the GNSS-viewwer PCB?

The GNSS-viewwer measures 100 × 50.1 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the GNSS-viewwer?

68 components, from 40 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the GNSS-viewwer design files?

From the hnz1102/GNSS-viewwer repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the GNSS-viewwer design in my own project?

The repository has no license, so all rights stay with hnz1102. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the GNSS-viewwer without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards