PCB
Huruvarshan·Automatischer-Kabelschneider·Hardware/PCB/v1.0/Mainboard/Mainboard.kicad_pcb
About the PCB
PCB is an open source ESP32 PCB design by Huruvarshan, published on GitHub under the MIT license. It is a 2-layer board measuring 100 × 75 mm, with 28 components from 15 distinct parts.
Its main chip is the ESP32-S3-WROOM-2, from the ESP32 family. Other key parts include the AP63203WU and TMC2209_SILENTSTEPSTICK. By type, the board carries 11 capacitors, 6 connectors, 5 ICs, 3 resistors, 2 switches and 1 inductor.
From the project
GitHub Verzeichnis für den automatischen Kabelschneider
Welcome to the hardware section of the Automatischer Kabelschneider (Automatic Cable Cutter) project.
- The PCB (Printed Circuit Board) design files are available here: ./PCB/
- The mechanical design files can be found here: ./Mechanical/
- A complete list of components required for the hardware build is available here: ./BOM.md
- Step-by-step instructions for assembling the hardware will be provided here.
Main components on the PCB
PCB bill of materials (BOM)
28 components, 15 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AP63203WU | TSOT-23-6 | U1 |
| 1 | ~ | Breackoutboard | U2 |
| 2 | TMC2209_SILENTSTEPSTICK | MODULE_TMC2209_SILENTSTEPSTICK | U3, U5 |
| 1 | ESP32-S3-WROOM-2 | ESP32-S3-WROOM-2 | U4 |
| 2 | Conn_01x04 | PhoenixContact_MC_1,5_4-G-3.81_1x04_P3.81mm_Horizontal | J1, J3 |
| 1 | Conn_02x02_Odd_Even | PinHeader_2x02_P2.54mm_Vertical | J2 |
| 3 | Conn_02x03_Odd_Even | PinHeader_2x03_P2.54mm_Vertical | J4, J5, J6 |
| 2 | SW_Push | SW_Push_1P1T_NO_6x6mm_H9.5mm | SW1, SW2 |
| 1 | 3u9 | L_Wurth_WE-LQSH-4020 | L1 |
| 2 | 100n | C_0805_2012Metric | C1, C6 |
| 1 | 10u | C_0805_2012Metric | C2 |
| 7 | 22u | C_0805_2012Metric | C3, C4, C5, C8, C9, C10, C11 |
| 1 | 1u | C_0805_2012Metric | C7 |
| 1 | 10k | R_0805_2012Metric | R1 |
| 2 | 5k1 | R_0805_2012Metric | R2, R3 |
PCB design files
The KiCad project lives in the Huruvarshan/Automatischer-Kabelschneider repository on GitHub; these links point at the commit this page was built from.
PCB: common questions
What microcontroller does the PCB use?
The PCB is built around the ESP32-S3-WROOM-2, from the ESP32 family.
How big is the PCB?
The PCB measures 100 × 75 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the PCB?
28 components, from 15 distinct parts. The full bill of materials is listed on this page.
Where can I download the PCB design files?
From the Huruvarshan/Automatischer-Kabelschneider repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the PCB design in my own project?
Yes, under the terms of its MIT license, which Huruvarshan chose for the repository.
Can I test firmware for the PCB without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Automatischer-Kabelschneider
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k