Rev 01

HyFiVeUser·HyFiVe·01_Logger/01_Basic_Logger/01_Electronics/Rev_01/Rev_01.kicad_pcb

Rev 01 PCB layout, top view — open source ESP32 board by HyFiVeUser

About the Rev 01 PCB

Rev 01 is an open source ESP32 PCB design by HyFiVeUser, published on GitHub under the CC-BY-SA-4.0 license. It is a 2-layer board measuring 55 × 85 mm, with 64 components from 29 distinct parts.

Its main chip is the ESP32-S3-WROOM-1U-N16R2, from the ESP32 family. Other key parts include the MP3213DH-LF-Z, THVD1429DT, RT9080-33GJ5 and LTC1540CS8#TRPBF. By type, the board carries 32 resistors, 8 transistors, 7 capacitors, 5 ICs, 1 connector and 1 switch.

It belongs with the power & battery and sensors designs in this gallery.

From the project

The hardware is designed and can be modified in KiCad 7. Therefore the folder /HyfiveLib contains custom footprints and schematics for the projects below.

The hardware is designed and can be modified in KiCad 7. Therefore the folder /HyfiveLib contains custom footprints and schematics for the projects below.

To select possible sensors to implement take a look into the subfolder ../04Sensors*. The list can of course be extended. So far all sensors except the ones by BlueRobotics are connected with Molex PicoBlade connectors. How to connect each sensor in hardware is described in the sensor readme.

Rev 01, from the project README
From the project README

Main components on the Rev 01

MP3213DH-LF-ZTHVD1429DTRT9080-33GJ5LTC1540CS8#TRPBFESP32-S3-WROOM-1U-N16R2

Rev 01 bill of materials (BOM)

64 components, 29 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
MP3213DH-LF-Z
IC1
1
THVD1429DT
THVD14x9
U1
1
RT9080-33GJ5
U2
1
LTC1540CS8#TRPBF
LTC1540
U3
1
ESP32-S3-WROOM-1U-N16R2
ESP32-S3-WROOM-1
U4
5
SS8050-G
Q1, Q2, Q3, Q5, Q9
3
MMFTP84
BSS83P
Q4, Q6, Q10
1
MEM2067-02-180-00-A
Micro_SD_Card
J9
4
53261-0471
Conn_01x04_MountingPin
I2C1, I2C2, Uart2, Uart2_RS485_V8
1
53261-0571
Conn_01x05_MountingPin
I2C3_5Pin1
1
55935-0230
Conn_01x02
Molex_Battery1
1
53261-0671
Conn_01x06_MountingPin
Molex_Usb1
1
3013
Conn_01x08
RTC1
1
434111025826
SW_DIP_x01
SW1
1
CD1206-B240
D_Schottky
D2
1
SRN4018-4R7M
4,7µ
L2
2
10n
C1, C19
2
1µ
C7, C8
1
TMK212BBJ106KG8T
10µ
C18
1
2,2n
C20
Show 9 more
QtyPartRefs
1
GCM21BC71E475KE36L
4,7µ
C21
4
100k
R1, R9, R10, R11
2
12k
R2, R24
2
470k
R3, R23
8
15k
R4, R5, R17, R18, R19, R22, R29, R30
4
1k
R6, R12, R15, R16
4
10k
R7, R8, R13, R14
4
1M
R20, R21, R25, R26
4
0
R40, R41, R42, R43

Rev 01 design files

The KiCad project lives in the HyFiVeUser/HyFiVe repository on GitHub; these links point at the commit this page was built from.

Rev 01: common questions

What microcontroller does the Rev 01 use?

The Rev 01 is built around the ESP32-S3-WROOM-1U-N16R2, from the ESP32 family.

How big is the Rev 01 PCB?

The Rev 01 measures 55 × 85 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Rev 01?

64 components, from 29 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Rev 01 design files?

From the HyFiVeUser/HyFiVe repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Rev 01 design in my own project?

Yes, under the terms of its CC-BY-SA-4.0 license, which HyFiVeUser chose for the repository.

Can I test firmware for the Rev 01 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in HyFiVe

Similar boards