Helios lasercube api
hypertechnic·helios_lasercube_api·hardware/Kicad_PCB_helios/Helios.kicad_pcb
About the Helios lasercube api PCB
Helios lasercube api is an open source Microchip SAM PCB design by hypertechnic, published on GitHub under the CC-BY-NC-4.0 license. It is a 2-layer board measuring 75.2 × 61.1 mm, with 97 components from 22 distinct parts.
Its main chip is the ATSAM4S, from the Microchip SAM family. Other key parts include the IP4220CZ6, AP2114, AN431B, ISA_DC-DC_converter and DAC084S085C. By type, the board carries 48 resistors, 31 capacitors, 9 ICs, 3 inductors, 2 connectors and 2 diodes.
From the project
api for manual control of lasercube via helios DAC
* https://bitlasers.com/helios-laser-dac/
Open source, low cost USB DAC for the ISP-DB25 (ILDA) laser protocol. Allows you to control an ILDA laser projector via computer over USB. Supports lots of third party software (see link above). This repository consists of: SDK (with examples in C++, Python and C#/.NET) Hardware (PCB schematic in KiCAD) Firmware (Atmel Studio project) Extras (firmware update tool, media etc.)
Main components on the Helios lasercube api
Helios lasercube api bill of materials (BOM)
97 components, 22 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | IP4220CZ6 | SOT457 | U1 |
| 1 | AP2114 | SOT-223 | U2 |
| 1 | AN431B | SOT-23 | U3 |
| 1 | ISA_DC-DC_converter | 10-SMD-6 | U4 |
| 1 | DAC084S085C | MSOP-10_3x3mm_Pitch0.5mm | U5 |
| 2 | TL084_v | TSSOP-14_4.4x5mm_Pitch0.65mm | U6, U8 |
| 1 | LM358 | SOIC-8_3.9x4.9mm_Pitch1.27mm | U7 |
| 1 | ATSAM4S | LQFP-64_10x10mm_Pitch0.5mm | U9 |
| 1 | 16MHz 18pF | Crystal_HC49-SD_SMD | Y1 |
| 1 | USB_B | USB_B | P1 |
| 1 | CONN_01X25-SHIELD | DB25 | P2 |
| 1 | F_Small | R_1206 | F1 |
| 2 | Led_Small | LED_0603 | D1, D2 |
| 3 | FILTER | R_0603 | L1, L2, L3 |
| 9 | 4.7uF | c_elec_4x5.3 | C1, C4, C6, C8, C9, C11, C23, C24 +1 |
| 18 | 100nF | C_0402 | C2, C3, C7, C10, C13, C14, C15, C16 +10 |
| 4 | 13pF | C_0402 | C12, C29, C31, C32 |
| 2 | 27 | R_0603 | R1, R2 |
| 11 | 150 | R_0603 | R3, R4, R5, R6, R7, R8, R9, R10 +3 |
| 18 | 10k | R_0603 | R14, R15, R18, R19, R20, R21, R23, R26 +10 |
Show 2 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 8 | 5.11k | R_0603 | R16, R17, R24, R25, R30, R32, R41, R42 |
| 9 | 1.65k | R_0603 | R22, R33, R34, R35, R36, R45, R46, R47 +1 |
Helios lasercube api design files
The KiCad project lives in the hypertechnic/helios_lasercube_api repository on GitHub; these links point at the commit this page was built from.
Helios lasercube api: common questions
What microcontroller does the Helios lasercube api use?
The Helios lasercube api is built around the ATSAM4S, from the Microchip SAM family.
How big is the Helios lasercube api PCB?
The Helios lasercube api measures 75.2 × 61.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Helios lasercube api?
97 components, from 22 distinct parts. The full bill of materials is listed on this page.
Where can I download the Helios lasercube api design files?
From the hypertechnic/helios_lasercube_api repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Helios lasercube api design in my own project?
It is published under CC-BY-NC-4.0, which limits how it may be reused; read the license before building on it.
Can I test firmware for the Helios lasercube api without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Microchip SAM firmware against it before you order a PCB.
Similar boards
Microchip SAM
Microcontroller Expansion Card
FrameworkComputer
26 × 30 mm24 parts2LCC-BY-4.01.1kMicrochip SAM
Taco Raven
VoronDesign
120 × 113 mm349 parts4LGPL-3.01.1kMicrochip SAM
Fpgaboy
Wren6991
50 × 50 mm89 parts4LNo license511Microchip SAM
OpenDropV4
GaudiLabs
124 × 115.4 mm118 parts2LGPL-3.0487Microchip SAM
ModulAdapter universal
GaudiLabs
100 × 69.5 mm45 parts2LGPL-3.0487Microchip SAM
Kira
kiibohd
366.9 × 114.3 mm400 partsCERN-OHL-1.2416