Music-Kit-Test
JacknCrack18·Music-Kit-Test·hardware/touch-kit/music-kit.kicad_pcb
About the Music-Kit-Test PCB
Music-Kit-Test is an open source ESP32 PCB design by JacknCrack18, published on GitHub under the MIT license. It is a 2-layer board measuring 134 × 75 mm, with 15 components from 13 distinct parts.
Its main chip is the ESP32-DevKitC, from the ESP32 family. Other key parts include the LM1117T-3.3 and ER_OLEDM0.91_1x-I2C. By type, the board carries 6 connectors, 3 ICs, 2 battery holders, 1 switch and 1 LED.
It belongs with the audio and displays & leds designs in this gallery.
From the project
Touch Music Kit is an ESP32-based music controller PCB with seven capacitive touch pads, a small OLED display, physical controls, addressable LED output, and a PAM8403 audio amplifier module interface.
Touch Music Kit is an ESP32-based music controller PCB with seven capacitive touch pads, a small OLED display, physical controls, addressable LED output, and a PAM8403 audio amplifier module interface.
- ESP32-DevKitC module as the main controller. - Seven on-board capacitive touch pads labeled S1 through S7. - 0.91 inch SSD1306 I2C OLED module. - Rotary encoder with integrated push switch. - Two 12 mm push buttons. - Slide power switch and power input connectors. - PAM8403 amplifier module header for audio output. - Speaker output intended for a 0.5 W, 8 ohm, 32 mm speaker through the…

Main components on the Music-Kit-Test
Music-Kit-Test bill of materials (BOM)
15 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM1117T-3.3 | TO-220-3_Horizontal_TabDown | U1 |
| 1 | ESP32-DevKitC | ESP32-DevKitC | U2 |
| 1 | ER_OLEDM0.91_1x-I2C | ER_OLEDM0.91_1x-I2C | U3 |
| 1 | Power | PinSocket_1x02_P2.54mm_Horizontal | J1 |
| 2 | DAC_JUMPPER | PinHeader_1x02_P2.54mm_Vertical | J3, J12 |
| 1 | Speakerdf | PinSocket_1x03_P2.54mm_Vertical | J4 |
| 1 | INPUTS | JST_XH_B8B-XH-A_1x08_P2.50mm_Vertical | J5 |
| 1 | Power Conn | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J6 |
| 2 | Push_Button_W12mm | Push_Button_W12mm | BT1, BT2 |
| 1 | RotaryEncoder_Switch_MP | RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | ENC1 |
| 1 | PAM8403 | PinHeader_1x11_P2.54mm_Vertical | PAM1 |
| 1 | Slide_Switch_SPDT_P3mm_10x5x10mm | Slide_Switch_SPDT_P3mm_10x5x10mm | SW1 |
| 1 | NEOPIXEL | PinSocket_1x03_P2.54mm_Vertical | LED1 |
Music-Kit-Test design files
The KiCad project lives in the JacknCrack18/Music-Kit-Test repository on GitHub; these links point at the commit this page was built from.
Music-Kit-Test: common questions
What microcontroller does the Music-Kit-Test use?
The Music-Kit-Test is built around the ESP32-DevKitC, from the ESP32 family.
How big is the Music-Kit-Test PCB?
The Music-Kit-Test measures 134 × 75 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Music-Kit-Test?
15 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the Music-Kit-Test design files?
From the JacknCrack18/Music-Kit-Test repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Music-Kit-Test design in my own project?
Yes, under the terms of its MIT license, which JacknCrack18 chose for the repository.
Can I test firmware for the Music-Kit-Test without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k