Starbie-V2
jacobgkhuynh-stack·Starbie-V2·PCB_kicad/Starbie-V2.kicad_pcb
About the Starbie-V2 PCB
Starbie-V2 is an open source ESP32 PCB design by jacobgkhuynh-stack, published on GitHub. It is a 2-layer board measuring 67 × 41 mm, with 8 components from 7 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 3 connectors, 2 ICs, 2 switches and 1 resistor.
It belongs with the iot & wireless and displays & leds designs in this gallery.
From the project
Hiya, this is for Half Life week 1 it's a Starbie: basically a desktop Tamagotchi but I made it into a compact rectangle creatively named the Starbie V2. How a Starbie works is it's basically the same thing as a Tamagotchi but you can tilt and move it to also interact with it. So
Hiya, this is for Half Life week 1 it's a Starbie: basically a desktop Tamagotchi but I made it into a compact rectangle creatively named the Starbie V2. How a Starbie works is it's basically the same thing as a Tamagotchi but you can tilt and move it to also interact with it. So it has a 0.96in 128x64 oled display, a XIAO-ESP32-C3 as the brain, a DHT11 for temp and humidity sensing, and a MPU6050 for motion tracking. Here's my BoMs Part | What it's for | Qty | Unit | Total | Vendor | | --- | --- | --- | --- | --- | --- | | XIAO ESP32-C3 | Dev board | 1 | $10.26 | $10.26 | ANSIKI IoT Store |…
Main components on the Starbie-V2
Starbie-V2 bill of materials (BOM)
8 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U1 |
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C3-SMD | U2 |
| 1 | Conn_01x04_Pin | Display_128x64_096_I2C | J1 |
| 1 | Conn_01x08_Pin | MPU6050_Module | J2 |
| 1 | Conn_01x02_Pin | PinHeader_1x02_P2.54mm_Vertical | J3 |
| 2 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2 |
| 1 | 10k | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
Starbie-V2 design files
The KiCad project lives in the jacobgkhuynh-stack/Starbie-V2 repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB_kicad/Starbie-V2.kicad_pcb
- SchematicPCB_kicad/Starbie-V2.kicad_sch
Starbie-V2: common questions
What microcontroller does the Starbie-V2 use?
The Starbie-V2 is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Starbie-V2 PCB?
The Starbie-V2 measures 67 × 41 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Starbie-V2?
8 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the Starbie-V2 design files?
From the jacobgkhuynh-stack/Starbie-V2 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Starbie-V2 design in my own project?
The repository has no license, so all rights stay with jacobgkhuynh-stack. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Starbie-V2 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k