Remote board

jiangmenglin·rc_car·remote_board/remote_board.kicad_pcb

Remote board layout, top view — open source ESP32 board by jiangmenglin

About the Remote board

Remote board is an open source ESP32 PCB design by jiangmenglin, published on GitHub. It is a 2-layer board measuring 100 × 70 mm, with 55 components from 26 distinct parts.

Its main chip is the ESP32-C3-WROOM-02-N4, from the ESP32 family. Other key parts include the TP4056-42-ESOP8 and AP2112K-3.3. By type, the board carries 19 resistors, 16 capacitors, 7 switches, 6 diodes, 4 connectors and 3 ICs.

It belongs with the power & battery and iot & wireless designs in this gallery.

From the project

ESP32-C3 双板遥控小车硬件:车控板 + 手持遥控板。KiCad 原理图/PCB 由 Python 代码生成,含 BOM、ERC 与 net 级校验。 | Dual-board RC car hardware built around ESP32-C3, with KiCad designs generated from Python.

一个用 代码生成 的遥控车硬件项目:车控板 + 手持遥控板,主控均为 ESP32-C3-WROOM-02。 原理图与 PCB 并非手绘,而是由 tools/ 下的 Python 生成器直接写出 KiCad 文件,因此布局、网络和 BOM 都可复现、可校验。

- 软开关:SW1 按下 → Q2 拉低 Q1 栅极 → 系统上电;MCU 通过 PWRHOLD(IO9) 驱动 Q3 维持电源,固件可自己关机。 - 电池检测:VBAT 经 R14/R15(100 k / 33 k)分压到 VBATSENSE,8.4 V → 约 2.08 V。 - 电机:TB6612FNG 的 VM 直接接电池(VBAT),A 通道驱动后轮、B 通道驱动转向,STBY 由 MCU 控制。 - USB-C:CC1/CC2 各 5.1 k 下拉;D+/D− 有 PESD3V3L1BA ESD 保护,直连 ESP32-C3 原生 USB。

Main components on the Remote board

Remote board bill of materials (BOM)

55 components, 26 distinct parts.

QtyPartRefs
1
ESP32-C3-WROOM-02-N4
U1
1
TP4056-42-ESOP8
U2
1
AP2112K-3.3
U3
1
1S Li-Po input
J1
1
2-axis joystick
J2
1
UART debug
J3
1
USB-C USB2.0
J4
1
POWER SLIDE
SW1
1
RESET
SW2
1
BOOT / IO9
SW3
1
A
SW4
1
B
SW5
1
C
SW6
1
D
SW7
2
PESD3V3L1BA,115
PESD3V3L1BA
D1, D2
1
Red
D3
2
Green
D4, D5
1
Blue
D6
5
10u / 10V X7R
C1, C2, C3, C4, C7
10
100n
C5, C8, C9, C10, C11, C12, C13, C14 +2
Show 6 more
QtyPartRefs
1
1u
C6
2
5.1k
R1, R2
1
2.4k / 1%
R3
6
1k
R4, R5, R8, R10, R13, R14
8
10k
R6, R7, R9, R15, R16, R17, R18, R19
2
100k
R11, R12

Remote board design files

The KiCad project lives in the jiangmenglin/rc_car repository on GitHub; these links point at the commit this page was built from.

Remote board: common questions

What microcontroller does the Remote board use?

The Remote board is built around the ESP32-C3-WROOM-02-N4, from the ESP32 family.

How big is the Remote board?

The Remote board measures 100 × 70 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Remote board?

55 components, from 26 distinct parts. The full bill of materials is listed on this page.

Where can I download the Remote board design files?

From the jiangmenglin/rc_car repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Remote board design in my own project?

The repository has no license, so all rights stay with jiangmenglin. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Remote board without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in rc_car

Similar boards