Car board
jiangmenglin·rc_car·car_board/car_board.kicad_pcb
About the Car board
Car board is an open source ESP32 PCB design by jiangmenglin, published on GitHub. It is a 2-layer board measuring 80 × 60 mm, with 54 components from 31 distinct parts.
Its main chip is the ESP32-C3-WROOM-02-N4, from the ESP32 family. Other key parts include the AP63203WU-7 and TB6612FNG. By type, the board carries 17 capacitors, 16 resistors, 6 diodes, 4 connectors, 3 ICs and 3 transistors.
It belongs with the power & battery and iot & wireless designs in this gallery.
From the project
ESP32-C3 双板遥控小车硬件:车控板 + 手持遥控板。KiCad 原理图/PCB 由 Python 代码生成,含 BOM、ERC 与 net 级校验。 | Dual-board RC car hardware built around ESP32-C3, with KiCad designs generated from Python.
一个用 代码生成 的遥控车硬件项目:车控板 + 手持遥控板,主控均为 ESP32-C3-WROOM-02。 原理图与 PCB 并非手绘,而是由 tools/ 下的 Python 生成器直接写出 KiCad 文件,因此布局、网络和 BOM 都可复现、可校验。
- 软开关:SW1 按下 → Q2 拉低 Q1 栅极 → 系统上电;MCU 通过 PWRHOLD(IO9) 驱动 Q3 维持电源,固件可自己关机。 - 电池检测:VBAT 经 R14/R15(100 k / 33 k)分压到 VBATSENSE,8.4 V → 约 2.08 V。 - 电机:TB6612FNG 的 VM 直接接电池(VBAT),A 通道驱动后轮、B 通道驱动转向,STBY 由 MCU 控制。 - USB-C:CC1/CC2 各 5.1 k 下拉;D+/D− 有 PESD3V3L1BA ESD 保护,直连 ESP32-C3 原生 USB。
Main components on the Car board
Car board bill of materials (BOM)
54 components, 31 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-WROOM-02-N4 | ESP32-C3-WROOM-02 | U1 |
| 1 | AP63203WU-7 | TSOT-23-6 | U2 |
| 1 | TB6612FNG | SSOP-24_5.3x8.2mm_P0.65mm | U3 |
| 1 | AO3401A AO3401A P-MOS | SOT-23 | Q1 |
| 2 | 2N7002 | SOT-23 | Q2, Q3 |
| 1 | 2S Li-Po input | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J1 |
| 1 | Drive motor | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J2 |
| 1 | Steering motor | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J3 |
| 1 | USB-C USB2.0 | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J4 |
| 1 | MF-MSMF250-2 2.5A hold PTC | Fuse_1812_4532Metric | F1 |
| 1 | POWER | SW_SPST_TL3342 | SW1 |
| 1 | RESET | SW_SPST_TL3342 | SW2 |
| 1 | BOOT / IO9 | SW_SPST_TL3342 | SW3 |
| 1 | SMBJ12A | D_SMB | D1 |
| 2 | SS24 | D_SMA | D2, D3 |
| 2 | PESD3V3L1BA,115 PESD3V3L1BA | D_SOD-323 | D4, D5 |
| 1 | Green | LED_0805_2012Metric | D6 |
| 1 | XAL5030-392MEC 3.9uH / 5A | L_Coilcraft_XAL5030-XXX | L1 |
| 8 | 100n | C_0805_2012Metric | C1, C2, C4, C7, C9, C11, C12, C14 |
| 1 | 10u / 25V X7R | C_1206_3216Metric | C3 |
Show 11 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 22u / 10V X7R | C_1206_3216Metric | C5, C6 |
| 1 | 1u | C_0805_2012Metric | C8 |
| 2 | 10u / 10V X7R | C_0805_2012Metric | C10, C15 |
| 1 | 47u / 16V X7R | C_1210_3225Metric | C13 |
| 2 | 100n / 50V | C_0805_2012Metric | C16, C17 |
| 6 | 100k | R_0805_2012Metric | R1, R3, R5, R6, R14, R16 |
| 4 | 10k | R_0805_2012Metric | R2, R10, R11, R13 |
| 2 | 1k | R_0805_2012Metric | R4, R12 |
| 1 | 47k | R_0805_2012Metric | R7 |
| 2 | 5.1k | R_0805_2012Metric | R8, R9 |
| 1 | 33k | R_0805_2012Metric | R15 |
Car board design files
The KiCad project lives in the jiangmenglin/rc_car repository on GitHub; these links point at the commit this page was built from.
- Layoutcar_board/car_board.kicad_pcb
- Schematiccar_board/car_board.kicad_sch
Car board: common questions
What microcontroller does the Car board use?
The Car board is built around the ESP32-C3-WROOM-02-N4, from the ESP32 family.
How big is the Car board?
The Car board measures 80 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Car board?
54 components, from 31 distinct parts. The full bill of materials is listed on this page.
Where can I download the Car board design files?
From the jiangmenglin/rc_car repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Car board design in my own project?
The repository has no license, so all rights stay with jiangmenglin. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Car board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in rc_car
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k