Fatigue-Measurement-Board

JJ80901·Fatigue-Measurement-Board·Fatigue Test Board/Fatigue Test Board.kicad_pcb

Fatigue-Measurement-Board layout, top view — open source STM32 board by JJ80901

About the Fatigue-Measurement-Board

Fatigue-Measurement-Board is an open source STM32 PCB design by JJ80901, published on GitHub. It is a 4-layer board measuring 58 × 85 mm, with 79 components from 38 distinct parts.

Its main chip is the STM32F103CBTx, from the STM32 family. Other key parts include the HT7533-1, MCP6001T-E/OT, TLV62569DBV, USBLC6-2SC6 and ADC141S626CIMM_NOPB. By type, the board carries 35 capacitors, 25 resistors, 9 ICs, 3 inductors, 2 connectors and 2 diodes.

It belongs with the test & measurement designs in this gallery.

From the project

This board is designed to process and digitize a ±10V analog signal from a laser displacement sensor, ensuring high-fidelity data acquisition for fatigue testing applications.

This board is designed to process and digitize a ±10V analog signal from a laser displacement sensor, ensuring high-fidelity data acquisition for fatigue testing applications.

The signal enters through a BNC connector, passes through ESD protection and an RF filter, and is then scaled down to a ±1.65V range using a resistor divider. A non-inverting summing amplifier shifts the signal into a 0-3.3V range, with a 1.65V bias generated by an op-amp follower from a half-resistor divider off the 3.3V power rail.

Main components on the Fatigue-Measurement-Board

Fatigue-Measurement-Board bill of materials (BOM)

79 components, 38 distinct parts.

QtyPartRefs
1
HT7533-1
U100
3
MCP6001T-E/OT
U101, U300, U301
1
TLV62569DBV
U102
1
STM32F103CBTx
U200
1
USBLC6-2SC6
U201
1
ADC141S626CIMM_NOPB
U302
1
REF3033AIDBZT
U303
1
16MHz
Y200
1
1332645
J200
1
031-5640-1010
J300
1
ACM2012-900-2P-T002
FL200
1
SW_Omron_B3FS
SW200
1
GREEN
D100
1
PESD3V3L1BA,115
D300
2
10n
L100, L200
1
10u
L101
11
100n
C100, C201, C202, C203, C204, C210, C300, C307 +3
4
1u
C101, C102, C206, C207
5
22u
C103, C104, C105, C106, C107
1
DNP
C108
Show 18 more
QtyPartRefs
6
10u
C200, C306, C309, C310, C311, C312
1
10n
C205
2
10p
C208, C209
2
1n
C301, C303
3
150p
C302, C304, C305
1
10R
R100
8
1k
R101, R102, R104, R300, R306, R308, R309, R310
1
100k
R103
1
22k
R105
2
5k1
R200, R201
2
10k
R202, R203
2
0R
R204, R312
1
1k5
R205
3
56k
R301, R302, R305
1
33k
R303
1
110k
R304
1
11k
R307
1
49R9
R311

Fatigue-Measurement-Board design files

The KiCad project lives in the JJ80901/Fatigue-Measurement-Board repository on GitHub; these links point at the commit this page was built from.

Fatigue-Measurement-Board: common questions

What microcontroller does the Fatigue-Measurement-Board use?

The Fatigue-Measurement-Board is built around the STM32F103CBTx, from the STM32 family.

How big is the Fatigue-Measurement-Board?

The Fatigue-Measurement-Board measures 58 × 85 mm, has 4 copper layers and is 1.6062 mm thick.

How many components are on the Fatigue-Measurement-Board?

79 components, from 38 distinct parts. The full bill of materials is listed on this page.

Where can I download the Fatigue-Measurement-Board design files?

From the JJ80901/Fatigue-Measurement-Board repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Fatigue-Measurement-Board design in my own project?

The repository has no license, so all rights stay with JJ80901. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Fatigue-Measurement-Board without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards