ATOM-Actuators
joshomak·ATOM-Actuators·electrical/ATOM_Motherboard.kicad_sch

About the ATOM-Actuators PCB
ATOM-Actuators is an open source ESP32 PCB design by joshomak, published on GitHub under the MIT license. It is a board, with 5 components from 5 distinct parts.
Its main chip is the ESP32-S3-DEVKITC-1-N8R2, from the ESP32 family. Other key parts include the AS5600 and TMC2209_SILENTSTEPSTICK. By type, the board carries 3 ICs, 1 module and 1 resistor.
It belongs with the robotics & motion designs in this gallery.
From the project
Contains the ATOM Robot Arm Actuator Modules.
This repository contains the source code, hardware files, and documentation for two quasi-direct-drive, closed-loop stepper motor actuators I designed and built as part of a robotic arm project during the 2024 winter break. From concept to completion, both actuators were designed, manufactured, and assembled in four days. Each actuator is 3D printed and features a unique gearbox design, an AS5600 magnetic encoder for precise position feedback, and is powered by a TMC2209 stepper motor driver controlled via an ESP32-S3 microcontroller.
Main components on the ATOM-Actuators
ATOM-Actuators bill of materials (BOM)
5 components, 5 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AS5600 | AS5600 | U1 |
| 1 | TMC2209_SILENTSTEPSTICK | MODULE_TMC2209_SILENTSTEPSTICK | U2 |
| 1 | ESP32-S3-DEVKITC-1-N8R2 | XCVR_ESP32-S3-DEVKITC-1-N8R2 | U7 |
| 1 | Stepper_Motor_bipolar | M1 | |
| 1 | 1K | R8 |
ATOM-Actuators design files
The KiCad project lives in the joshomak/ATOM-Actuators repository on GitHub; these links point at the commit this page was built from.
ATOM-Actuators: common questions
What microcontroller does the ATOM-Actuators use?
The ATOM-Actuators is built around the ESP32-S3-DEVKITC-1-N8R2, from the ESP32 family.
How many components are on the ATOM-Actuators?
5 components, from 5 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the ATOM-Actuators design files?
From the joshomak/ATOM-Actuators repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the ATOM-Actuators design in my own project?
Yes, under the terms of its MIT license, which joshomak chose for the repository.
Can I test firmware for the ATOM-Actuators without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k