Ncv7240-driver
jussty·ncv7240-driver
About the Ncv7240-driver PCB
Ncv7240-driver is an open source ESP32 PCB design by jussty, published on GitHub. It is a 4-layer board measuring 200 × 120 mm, with 68 components from 21 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the AP33772S, NCV7240 and TPS62932. By type, the board carries 33 diodes, 15 capacitors, 7 ICs, 7 resistors, 5 connectors and 1 inductor.
It belongs with the iot & wireless designs in this gallery.
From the project
KiCad 8 PCB: 4x NCV7240 octal low-side drivers + ESP32-S3 + AP33772S USB-C PD EPR (24V)
A KiCad 8 project for a compact controller board that:
- Negotiates 24 V from a USB-C PD 3.1 EPR source via the AP33772S sink controller. - Hosts an ESP32-S3 MCU for Wi-Fi/BT control, configuration and host comms. - Drives 32 low-side switched outputs at 24 V using 4 × NCV7240 octal low-side drivers (SPI-controlled).
- The AP33772S handles all CC negotiation/PPS/EPR; the ESP32 just configures the request profile over I²C and reads VBUS / status telemetry. - The 4 NCV7240s share SCK/MOSI/MISO/RSTB/SI on a single SPI bus; each has its own /CSB from the ESP32. Output enable is per-channel via…
Main components on the Ncv7240-driver
Ncv7240-driver bill of materials (BOM)
68 components, 21 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AP33772S | QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U1 |
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U2 |
| 4 | NCV7240 | SSOP-24_5.3x8.2mm_P0.65mm | U3, U4, U5, U6 |
| 1 | TPS62932 | SOT-23-6 | U7 |
| 1 | USB-C | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | OUT1-8 | TerminalBlock_Phoenix_MKDS-1,5-8_1x08_P5.00mm_Horizontal | J2 |
| 1 | OUT9-16 | TerminalBlock_Phoenix_MKDS-1,5-8_1x08_P5.00mm_Horizontal | J3 |
| 1 | OUT17-24 | TerminalBlock_Phoenix_MKDS-1,5-8_1x08_P5.00mm_Horizontal | J4 |
| 1 | OUT25-32 | TerminalBlock_Phoenix_MKDS-1,5-8_1x08_P5.00mm_Horizontal | J5 |
| 1 | SMBJ33A | D_SMB | D1 |
| 32 | B260A | D_SMA | D2, D3, D4, D5, D6, D7, D8, D9 +24 |
| 1 | 4.7uH/2A | L_Bourns-SRN6045TA | L1 |
| 1 | 100uF/50V | CP_Elec_10x10.5 | C1 |
| 5 | 10uF/50V | C_1210_3225Metric | C2, C11, C13, C15, C17 |
| 1 | 22uF | C_0805_2012Metric | C3 |
| 1 | 10uF | C_0805_2012Metric | C4 |
| 7 | 100nF | C_0603_1608Metric | C5, C6, C7, C10, C12, C14, C16 |
| 3 | 10k | R_0603_1608Metric | R1, R2, R3 |
| 2 | 4.7k | R_0603_1608Metric | R4, R5 |
| 1 | 100k | R_0603_1608Metric | R6 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 20k | R_0603_1608Metric | R7 |
Ncv7240-driver design files
The KiCad project lives in the jussty/ncv7240-driver repository on GitHub; these links point at the commit this page was built from.
- Layoutncv7240-driver.kicad_pcb
- Schematicncv7240-driver.kicad_sch
Ncv7240-driver: common questions
What microcontroller does the Ncv7240-driver use?
The Ncv7240-driver is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the Ncv7240-driver PCB?
The Ncv7240-driver measures 200 × 120 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Ncv7240-driver?
68 components, from 21 distinct parts. The full bill of materials is listed on this page.
Where can I download the Ncv7240-driver design files?
From the jussty/ncv7240-driver repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Ncv7240-driver design in my own project?
The repository has no license, so all rights stay with jussty. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Ncv7240-driver without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k