9 open source boards using the TPS62932
Real designs built with the TPS62932, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
ESC-Development-Board
10x-Aero
66 × 61.8 mm82 parts4LNo license75FPGA
GammaSpectrometer
RobertGawron
100 × 100 mm291 parts4LMIT16Raspberry Pi
YOGA - Yet anOther GPIB Adapter
mschwingen
85 × 56 mm80 parts2LNo license10Raspberry Pi
2026-FE-The-Rdacted
Spaceflakes
65 × 56 mm42 parts4LNo license1ESP32
ESP32-controlled peltier controller-CE-pre certified untested
manhoosbilli1
109.5 × 61.1 mm161 parts4LNo license0ESP32
Smart peltier driver esp32-v1
manhoosbilli1
94 × 48.1 mm84 parts2LNo license0STM32
Am32-bldc esc
adsayan7
66 × 61.8 mm82 parts4LNo license0ESP32
Ncv7240-driver
jussty
200 × 120 mm68 parts4LNo license0Simulator-Interface-Board
M2I-CySat
80.2 × 80.2 mm24 parts2LNo license0
How designs wire the TPS62932
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the TPS62932 connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a series capacitor on 8 of 9 designs, most often 100 nF.
- The SS pin has a capacitor to GND on 8 of 8 designs, most often 33 nF (then 47 nF).
- The FB pin has a resistor to GND on 8 of 8 designs, most often 10 kΩ (then 82 kΩ).
- The VIN pin has a decoupling capacitor on 7 of 9 designs, most often 100 nF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VINpin 3 | Connected to: BATT 67% · a signal 22% |
|
| GNDpin 4 | Connected to: GND 89% | — |
| SWpin 5 | Connected to: Signal 100% |
|
| BSTpin 6 | Connected to: Signal 89% |
|
| SSpin 7 | Connected to: Signal 100% |
|
| FBpin 8 | Connected to: Signal 100% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ESC-Development-Board by 10x-Aero, GammaSpectrometer by RobertGawron, YOGA - Yet anOther GPIB Adapter by mschwingen and 2026-FE-The-Rdacted by Spaceflakes.
The TPS62932 in open source designs
The gallery holds 9 open source boards using the TPS62932 from 9 GitHub repositories; a typical one measures about 85 × 61.8 mm and carries around 82 components.
67% use four copper layers or more, and 11% carry an open source license.
The most starred is ESC-Development-Board by 10x-Aero.
Parts used alongside the TPS62932
Microcontrollers on boards using the TPS62932
What boards using the TPS62932 are built for
TPS62932: common questions
Where can I find a TPS62932 reference design?
Each of the 9 boards on this page is a real design using the TPS62932. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS62932 SW pin connected?
The SW pin has a series capacitor on 8 of 9 designs, most often 100 nF. Counted from the KiCad layouts of 9 open source designs using the TPS62932.
How is the TPS62932 SS pin connected?
The SS pin has a capacitor to GND on 8 of 8 designs, most often 33 nF (then 47 nF). Counted from the KiCad layouts of 9 open source designs using the TPS62932.
What resistor goes on the TPS62932 FB pin?
The FB pin has a resistor to GND on 8 of 8 designs, most often 10 kΩ (then 82 kΩ). Counted from the KiCad layouts of 9 open source designs using the TPS62932.
What parts are used alongside the TPS62932?
The DRV8300DPWR, ESP32-S3-WROOM-1-N16R8, INA180B2, STM32F051K8Ux and TPS22811LRPWR_C17294173 appear in the most repositories here.
Which microcontrollers do boards using the TPS62932 use?
Most are built on ESP32 (3), Raspberry Pi (2), STM32 (2) and FPGA (1).
How big is a typical board using the TPS62932?
The median is 85 × 61.8 mm, and 33% are two-layer designs.
What is the most popular open source board using the TPS62932?
By GitHub stars, ESC-Development-Board by 10x-Aero, with 75 stars.
Can I simulate one of these boards using the TPS62932 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.