Eeg ads1299
kaanpars·16_channels_eeg_card·v1-ads1299/eeg_ads1299.kicad_pcb
About the Eeg ads1299 PCB
Eeg ads1299 is an open source PCB design by kaanpars, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 66 × 71.5 mm, with 100 components from 21 distinct parts.
Other key parts include the ADS1299IPAGR, LP2985-50DBVR and LP2985-33DBVR. By type, the board carries 52 resistors, 39 capacitors, 4 ICs, 3 connectors and 2 diodes.
It belongs with the sensors designs in this gallery.
From the project
I designed cards both in INA333 + TLV4333 and ADS1299. It is up to you which analog or digital output you should want to get. Importing restrictions in Turkey dragged me to designing my own sensor cards. ENJOY!
A 16-channel EEG acquisition board, designed twice: first with discrete analog parts (v0), then around TI's ADS1299 (v1). Both versions use the same electrode connector, so one set of cables works with either board.
v0 builds the whole analog signal chain by hand and verifies it in SPICE. v1 solves the same problem with a dedicated EEG chip. It is smaller, quieter and better suited to dry electrodes, but it costs more. The project is about comparing the two approaches.

Main components on the Eeg ads1299
Eeg ads1299 bill of materials (BOM)
100 components, 21 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | ADS1299IPAGR | TQFP-64_10x10mm_P0.5mm | U1, U2 |
| 1 | LP2985-50DBVR | SOT-23-5 | U3 |
| 1 | LP2985-33DBVR | SOT-23-5 | U4 |
| 1 | BATT 2S | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J1 |
| 1 | ELEKTROT 2x20 | IDC-Header_2x20_P2.54mm_Vertical | J2 |
| 1 | MCU SPI 2x6 | PinHeader_2x06_P2.54mm_Vertical | J3 |
| 1 | SS14 | D_SMA | D1 |
| 1 | GREEN | LED_0805_2012Metric | D2 |
| 1 | 10u 25V | C_0805_2012Metric | C1 |
| 23 | 1u | C_0805_2012Metric | C2, C7, C8, C9, C10, C11, C12, C14 +15 |
| 2 | 10N 10n | C_0805_2012Metric | C3, C5 |
| 6 | 10U 10u | C_0805_2012Metric | C4, C6, C13, C16, C29, C32 |
| 4 | 100N 100n | C_0805_2012Metric | C17, C21, C33, C37 |
| 2 | 100u 6.3V | C_1206_3216Metric | C18, C34 |
| 1 | 1.5N 1.5n | C_0805_2012Metric | C39 |
| 1 | 2k | R_0805_2012Metric | R1 |
| 33 | 4.99K 4.99k | R_0805_2012Metric | R2, R3, R4, R5, R6, R7, R8, R9 +25 |
| 1 | 1M | R_0805_2012Metric | R35 |
| 1 | 0R | R_0805_2012Metric | R36 |
| 1 | 470K 470k | R_0805_2012Metric | R37 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 15 | 10K 10k | R_0805_2012Metric | R38, R39, R40, R41, R42, R43, R44, R45 +7 |
Eeg ads1299 design files
The KiCad project lives in the kaanpars/16_channels_eeg_card repository on GitHub; these links point at the commit this page was built from.
Eeg ads1299: common questions
How big is the Eeg ads1299 PCB?
The Eeg ads1299 measures 66 × 71.5 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Eeg ads1299?
100 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Eeg ads1299 design files?
From the kaanpars/16_channels_eeg_card repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Eeg ads1299 design in my own project?
Yes, under the terms of its GPL-3.0 license, which kaanpars chose for the repository.
More boards in 16_channels_eeg_card
Similar boards
Sensor smd
scottbez1
40 × 20 mm5 parts2LApache-2.04.2kSensors
StuckAtPrototype
15.2 × 9 mm14 parts4LApache-2.03.8kMicrophone
Mentra-Community
5.5 × 6.1 mm6 parts2LMIT1.2kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kPots
shanteacontrols
390 × 93 mm75 parts2LApache-2.0956USB
shanteacontrols
52 × 12.6 mm6 parts2LApache-2.0956