Claude-3d printing
kalmehdar·claude-3d-printing·hardware/led-bar/led-bar.kicad_pcb
About the Claude-3d printing PCB
Claude-3d printing is an open source ESP32 PCB design by kalmehdar, published on GitHub under the MIT license. It is a 2-layer board measuring 200 × 36 mm, with 54 components from 16 distinct parts.
Its main chip is the ESP32-C3-WROOM-02-N4, from the ESP32 family. Other key parts include the AP2112K-3.3, 74AHCT1G125 and USBLC6-2SC6. By type, the board carries 23 capacitors, 16 diodes, 7 resistors, 4 ICs, 2 switches and 1 connector.
It belongs with the iot & wireless designs in this gallery.
From the project
Design 3D prints with Claude Code: OpenSCAD per-colour export, mesh checks, a Print Bench preview page, example designs, skills and agents
A 1U panel for a 10-inch rack: 16 addressable LEDs and an ESP32-C3 on one board, behind a printed faceplate with a white diffuser window. Powered and flashed over one USB-C cable, and runs WLED, so it's controlled from a phone or Home Assistant.
Designed end to end with Claude Code: the specs, the circuit, the board layout, the routing, the checks, the order files and the faceplate. Not built yet. Before ordering, a person works through REVIEW.md.

Main components on the Claude-3d printing
Claude-3d printing bill of materials (BOM)
54 components, 16 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-WROOM-02-N4 | ESP32-C3-WROOM-02 | U1 |
| 1 | AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | 74AHCT1G125 | SOT-23-5 | U3 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U4 |
| 1 | C2894897 USB-C | USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01A | J1 |
| 1 | C20802 1.5A hold | Fuse_1206_3216Metric | F1 |
| 1 | C318884 RESET | SW_Push_1P1T_XKB_TS-1187A | SW1 |
| 1 | C318884 BOOT | SW_Push_1P1T_XKB_TS-1187A | SW2 |
| 16 | WS2812B | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1, D2, D3, D4, D5, D6, D7, D8 +8 |
| 1 | C165531 470uF 16V | CP_Elec_8x10 | C1 |
| 3 | 1UF 1uF | C_0603_1608Metric | C2, C3, C6 |
| 1 | 10UF 10uF | C_0805_2012Metric | C4 |
| 18 | 100NF 100nF | C_0603_1608Metric | C5, C7, C8, C9, C10, C11, C12, C13 +10 |
| 2 | 5.1K 5.1k | R_0603_1608Metric | R1, R2 |
| 4 | 10K 10k | R_0603_1608Metric | R3, R4, R5, R7 |
| 1 | 390 | R_0603_1608Metric | R6 |
Claude-3d printing design files
The KiCad project lives in the kalmehdar/claude-3d-printing repository on GitHub; these links point at the commit this page was built from.
Claude-3d printing: common questions
What microcontroller does the Claude-3d printing use?
The Claude-3d printing is built around the ESP32-C3-WROOM-02-N4, from the ESP32 family.
How big is the Claude-3d printing PCB?
The Claude-3d printing measures 200 × 36 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Claude-3d printing?
54 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Claude-3d printing design files?
From the kalmehdar/claude-3d-printing repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Claude-3d printing design in my own project?
Yes, under the terms of its MIT license, which kalmehdar chose for the repository.
Can I test firmware for the Claude-3d printing without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k