Hackclub half life
KartikMarkan·hackclub-half-life·Project1/pcb/kicad-pcb-design/StarbieProject1/StarbieProject1.kicad_pcb
About the Hackclub half life PCB
Hackclub half life is an open source ESP32 PCB design by KartikMarkan, published on GitHub. It is a 2-layer board measuring 70 × 90 mm, with 9 components from 8 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 2 ICs, 2 connectors, 2 switches, 2 resistors and 1 diode.
It belongs with the displays & leds and sensors designs in this gallery.
From the project
- Language: C++ (Arduino) - Display Library: Adafruit GFX + Adafruit SSD1306 - Sensor Library: Adafruit DHT - Communication: I2C (Wire.h) - Baud Rate: 115200 (Serial debugging)
- Language: C++ (Arduino) - Display Library: Adafruit GFX + Adafruit SSD1306 - Sensor Library: Adafruit DHT - Communication: I2C (Wire.h) - Baud Rate: 115200 (Serial debugging)
I started off by following the Starbie PCB design. I did this by first downloading the KiCad software on my computer and connecting it to GitHub. After that, I watched 5 minutes of a 30 min youtube (its called Beginner's Guide to PCB Design in 30 Minutes by Tinkering Techie). I followed along to the instructions, and it took me ten whole minutes(lol):

Main components on the Hackclub half life
Hackclub half life bill of materials (BOM)
9 components, 8 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U1 |
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C6-DIP | U2 |
| 1 | Conn_01x04_Pin | Imported Display_128x64_096_I2C | J1 |
| 1 | Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J2 |
| 2 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2 |
| 1 | LED | LED_D5.0mm | D1 |
| 1 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 1 | 1k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2 |
Hackclub half life design files
The KiCad project lives in the KartikMarkan/hackclub-half-life repository on GitHub; these links point at the commit this page was built from.
Hackclub half life: common questions
What microcontroller does the Hackclub half life use?
The Hackclub half life is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Hackclub half life PCB?
The Hackclub half life measures 70 × 90 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Hackclub half life?
9 components, from 8 distinct parts. The full bill of materials is listed on this page.
Where can I download the Hackclub half life design files?
From the KartikMarkan/hackclub-half-life repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Hackclub half life design in my own project?
The repository has no license, so all rights stay with KartikMarkan. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Hackclub half life without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k