Fader-Module
KiloanTV·DMX-Console·hardware/Fader-Module/Fader-Module.kicad_pcb
About the Fader-Module
Fader-Module is an open source STM32 PCB design by KiloanTV, published on GitHub. It is a 4-layer board measuring 161.1 × 264 mm, with 101 components from 38 distinct parts.
Its main chip is the STM32F072CBT6, from the STM32 family. Other key parts include the MCP23017_SS, XC6206PXXXMR-REGULATOR_LINEAR, PRTR5V0U2X, W5500 and L9110S. By type, the board carries 33 capacitors, 16 diodes, 13 connectors, 12 switches, 9 ICs and 9 resistors.
From the project
Nodes to build a DMX Console.
I really wanted to build my own DMX Console but with modules and nodes so everyone can make a combination which work for themself. I havent designed the display driver board and the network switch yet but that will be in the V2 in the future.

Main components on the Fader-Module
Fader-Module bill of materials (BOM)
101 components, 38 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F072CBT6 | LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | MCP23017_SS | SSOP-28_5.3x10.2mm_P0.65mm | U2 |
| 1 | XC6206PXXXMR-REGULATOR_LINEAR XC6206PxxxMR-Regulator_Linear | SOT-23 | U3 |
| 1 | PRTR5V0U2X | SOT-143 | U4 |
| 1 | W5500 | LQFP-48_7x7mm_P0.5mm | U5 |
| 4 | L9110S | SOIC127P599X172-8N | U6, U7, U8, U9 |
| 4 | X32 Fader (without Motor) | x32-fader | X1, X2, X3, X4 |
| 1 | CRYSTAL_GND24 Crystal_GND24 | Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y2 |
| 1 | External Power | SolderWire-0.25sqmm_1x02_P4.5mm_D0.65mm_OD2mm | J1 |
| 1 | USB_C_RECEPTACLE_USB2.0 USB_C_Receptacle_USB2.0 | USB_C_HRO_TYPE-C-31-M-12 | J2 |
| 1 | C32713274 ExpansionHeader | PinHeader_1x08_P2.54mm_Vertical | J3 |
| 1 | C5188434 Motor_Powerrail | TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mm | J4 |
| 1 | RJ45_HANRUN_HR911105A_HORIZONTAL RJ45_Hanrun_HR911105A_Horizontal | RJ45_Hanrun_HR911105A_Horizontal | J5 |
| 1 | MOTOR1_OUT Motor1_Out | SolderWire-0.25sqmm_1x02_P4.2mm_D0.65mm_OD1.7mm | J6 |
| 1 | MOTOR2_OUT Motor2_Out | SolderWire-0.25sqmm_1x02_P4.2mm_D0.65mm_OD1.7mm | J7 |
| 1 | MOTOR3_OUT Motor3_Out | SolderWire-0.25sqmm_1x02_P4.2mm_D0.65mm_OD1.7mm | J8 |
| 1 | MOTOR4_OUT Motor4_Out | SolderWire-0.25sqmm_1x02_P4.2mm_D0.65mm_OD1.7mm | J9 |
| 4 | OLED_128X64 OLED_128x64 | OLED_128x64 | J10, J11, J12, J13 |
| 2 | C116647 SW_SPST | SW_SPST_TL3342 | BOOT1, RST1 |
| 2 | 500MA 500mA | Fuse_1206_3216Metric | F2, F3 |
Show 18 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 12 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8 +4 |
| 12 | 1N4148 | D_DO-35_SOD27_P7.62mm_Horizontal | D2, D3, D4, D9, D10, D11, D12, D13 +4 |
| 1 | C19273151 Active_LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D5 |
| 1 | C19171392 Link_LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D6 |
| 1 | C19273150 Duplex_LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D7 |
| 1 | C19273152 Speed_LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D8 |
| 1 | C3344 47uF ALU elektrolytic | C_Elec_6.3x5.4 | C1 |
| 2 | 10UF 10uF | C_0603_1608Metric | C2, C33 |
| 16 | 100NF 100nF | C_0402_1005Metric | C3, C5, C6, C8, C9, C10, C11, C12 +8 |
| 2 | 1UF 1uF | C_0402_1005Metric | C4, C7 |
| 2 | 22PF 22pF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C28, C29 |
| 1 | C2930060 12,4k ohm 1% | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C31 |
| 2 | 10NF 10nF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C34, C35 |
| 6 | C105881 330 ohm | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C36, C37, C38, C39, C43, C44 |
| 1 | C23631 1nF 2kV | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C42 |
| 4 | C558584 4.7k ohm | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R7, R8, R9 |
| 1 | C46961738 1M ohm | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R2 |
| 4 | 5.1K 5.1k | R_0402_1005Metric | R3, R4, R5, R6 |
Fader-Module design files
The KiCad project lives in the KiloanTV/DMX-Console repository on GitHub; these links point at the commit this page was built from.
Fader-Module: common questions
What microcontroller does the Fader-Module use?
The Fader-Module is built around the STM32F072CBT6, from the STM32 family.
How big is the Fader-Module?
The Fader-Module measures 161.1 × 264 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Fader-Module?
101 components, from 38 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Fader-Module design files?
From the KiloanTV/DMX-Console repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Fader-Module design in my own project?
The repository has no license, so all rights stay with KiloanTV. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Fader-Module without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in DMX-Console
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k