M5stack board unitree brushless digital servo
kim-xps12·m5stack_board_unitree_brushless_digital_servo
About the M5stack board unitree brushless digital servo
M5stack board unitree brushless digital servo is an open source PCB design by kim-xps12, published on GitHub under the MIT license. It is a 2-layer board measuring 50 × 35 mm, with 24 components from 17 distinct parts.
Other key parts include the 74LVC1G14, XC6206P332MR, 74LVC1G126 and 74LVC1G125. By type, the board carries 7 connectors, 7 capacitors, 4 ICs, 4 resistors, 1 fuse and 1 diode.
It belongs with the robotics & motion designs in this gallery.
From the project
Unitree Servo UART Board for M5Stack: auto-direction 4 Mbps half-duplex TTL bus for Unitree J288 / S288 brushless digital servos (KiCad 9, JLCPCB PCBA)
This board connects Unitree J288 / S288 brushless digital servos to an M5Stack controller (e.g. AtomS3R). The servo bus is a single-wire, half-duplex TTL bus (8N1, 4 Mbps). The board supports 4 Mbps only: change the baud rate of the servos to 4 Mbps with the official Unitree tool before use. The board switches between transmit and receive by itself from the TX signal, so the controller needs no direction pin. All logic runs at 3.3 V. The design is ready for JLCPCB assembly (PCBA).

Main components on the M5stack board unitree brushless digital servo
M5stack board unitree brushless digital servo bill of materials (BOM)
24 components, 17 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 74LVC1G14 | SOT-23-5_HandSoldering | U1 |
| 1 | XC6206P332MR | SOT-23 | U2 |
| 1 | 74LVC1G126 | SOT-23-5_HandSoldering | U3 |
| 1 | 74LVC1G125 | SOT-23-5_HandSoldering | U4 |
| 1 | XT30UPB-M | AMASS_XT30UPB-M_1x02_P5.0mm_Vertical | J1 |
| 1 | ZX-HY2.0-4PZZ | HY2.0-4P_1x04_P2.00mm_Vertical | J2 |
| 5 | B3B-PH-K-S(LF)(SN) | JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J3, J4, J5, J6, J7 |
| 1 | MINI 15A | Fuseholder_Blade_Mini_XFCN_XF-508P-B-B | F1 |
| 1 | RB751V-40 | D_SOD-323_HandSoldering | D1 |
| 3 | 0.1u | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C4, C5 |
| 2 | 1u | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C3 |
| 1 | 100p | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C6 |
| 1 | 100u 50V | CP_Elec_6.3x7.7 | C7 |
| 1 | 68k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 1 | 47 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2 |
| 1 | 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
| 1 | 470 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4 |
M5stack board unitree brushless digital servo design files
The KiCad project lives in the kim-xps12/m5stack_board_unitree_brushless_digital_servo repository on GitHub; these links point at the commit this page was built from.
M5stack board unitree brushless digital servo: common questions
How big is the M5stack board unitree brushless digital servo?
The M5stack board unitree brushless digital servo measures 50 × 35 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the M5stack board unitree brushless digital servo?
24 components, from 17 distinct parts. The full bill of materials is listed on this page.
Where can I download the M5stack board unitree brushless digital servo design files?
From the kim-xps12/m5stack_board_unitree_brushless_digital_servo repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the M5stack board unitree brushless digital servo design in my own project?
Yes, under the terms of its MIT license, which kim-xps12 chose for the repository.
Similar boards
Stack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kCube batteryboard
willem-pennings
95 × 95 mm4 parts2LGPL-3.01.1kTrollerv2
rene-dev
100 × 75 mm33 parts4LGPL-3.0979Powerstep
rene-dev
95.2 × 71.5 mm28 parts4LGPL-3.097911ua
rene-dev
57.3 × 19 mm26 parts2LGPL-3.0979Diff driver
rene-dev
32 × 22 mm14 parts2LGPL-3.0979