Ublink
koraa·ublink·hardware/ublink.kicad_pcb
About the Ublink PCB
Ublink is an open source ESP32 PCB design by koraa, published on GitHub. It is a 2-layer board measuring 67 × 54.5 mm, with 55 components from 29 distinct parts.
Its main chip is the ESP32-WROOM-32U, from the ESP32 family. Other key parts include the 3.3V3 Regul, CH340G, HF115F_005-1ZS3 and EL817S. By type, the board carries 14 resistors, 8 ICs, 8 connectors, 6 transistors, 5 diodes and 5 capacitors.
From the project
PWM control for high power LEDs
ESP32 CPU Access console via USB External antenna support High Voltage Relais to turn
Hardware is licensed under CERN Open Hardware Licence v1.2. Software is licensed under MIT license.
Main components on the Ublink
Ublink bill of materials (BOM)
55 components, 29 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 3.3V3 Regul | lm-1117 | U1 |
| 1 | CH340G | CH403G | U2 |
| 1 | HF115F_005-1ZS3 | HF115F_005-1ZS3 | U3 |
| 1 | ESP32-WROOM-32U | ESP32-WROOM-32U | U4 |
| 4 | EL817S | EL817S | U5, U6, U7, U8 |
| 2 | STN3NF06L | SOT-23_Handsoldering | Q1, Q6 |
| 4 | RU6099 | TO-220-3_Vertical | Q2, Q3, Q4, Q5 |
| 1 | 12Mhz | Crystal_SMD_5032-2pin_5.0x3.2mm_HandSoldering | Y1 |
| 1 | USB_B_Micro | USB_Micro-B_Molex-105017-0001 | J1 |
| 1 | AC1 | KF301-5.0-3P | J2 |
| 1 | 5V Trafo | KF301-5.0-2P | J3 |
| 3 | Screw_Terminal_01x02 | KF301-5.0-2P | J4, J5, J7 |
| 1 | Pin Header | Pin_Header_Straight_2x05_Pitch2.54mm | J8 |
| 1 | Screw_Terminal_01x02 | KF301-5.0-3P | J9 |
| 1 | CP2 | C_0805_HandSoldering | 2u2 |
| 1 | C8 | C_0805_HandSoldering | 10u1 |
| 1 | C7 | C_0805_HandSoldering | 10u2 |
| 1 | CP1 | CP_Tantalum_Case-B_EIA-3528-21_Reflow | 100u1 |
| 1 | CP2 | CP_Tantalum_Case-B_EIA-3528-21_Reflow | 100u2 |
| 2 | SW_Push | pushbutton_2 | SW1, SW2 |
Show 9 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | JUC-31F | JUC-31F | SW3 |
| 4 | 18V | D_SOD-323_HandSoldering | D1, D2, D3, D4 |
| 1 | D | D_SOD-323_HandSoldering | D5 |
| 2 | 22p | C_0805_HandSoldering | C1, C3 |
| 1 | 0.1u | C_0805_HandSoldering | C4 |
| 2 | 100n | C_0805_HandSoldering | C5, C6 |
| 8 | 100 | R_0805_HandSoldering | R1, R2, R3, R4, R8, R9, R10, R11 |
| 2 | 10k | R_0805_HandSoldering | R5, R7 |
| 4 | 20k | R_0805_HandSoldering | R12, R13, R14, R15 |
Ublink design files
The KiCad project lives in the koraa/ublink repository on GitHub; these links point at the commit this page was built from.
Ublink: common questions
What microcontroller does the Ublink use?
The Ublink is built around the ESP32-WROOM-32U, from the ESP32 family.
How big is the Ublink PCB?
The Ublink measures 67 × 54.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Ublink?
55 components, from 29 distinct parts. The full bill of materials is listed on this page.
Where can I download the Ublink design files?
From the koraa/ublink repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Ublink design in my own project?
The repository has no license, so all rights stay with koraa. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Ublink without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k