Ohara-75
krishivjoshi219-collab·Ohara-75
About the Ohara-75 PCB
Ohara-75 is an open source ESP32 PCB design by krishivjoshi219-collab, published on GitHub. It is a 2-layer board measuring 98 × 98 mm, with 40 components from 28 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the TP4056-42-ESOP8 and AP2112K-3.3. By type, the board carries 12 capacitors, 10 resistors, 5 connectors, 5 switches, 3 ICs and 3 diodes.
It belongs with the power & battery, keyboards and displays & leds designs in this gallery.
From the project
hi this is my first readme for my 3rd pcb project !!!!!!!! pls dont judge my spelling i am 13 and i type too fast :sob: also this is the same voice as my JOURNAL.md because that is just how i write ok !!!!!!!
hi this is my first readme for my 3rd pcb project !!!!!!!! pls dont judge my spelling i am 13 and i type too fast :sob: also this is the same voice as my JOURNAL.md because that is just how i write ok !!!!!!!
Ohara-75 is a handheld e-ink reader i made for reading MANGA and novels with 0 eye strain !!!!!!!!!
it has a 7.5 inch e-paper screen, an ESP32-S3, a microSD card for all my offline books, a LiPo battery, USB-C charging, two Kailh Choc page buttons, and a 3D printed case. it is 98x98mm because JLCPCB is cheap only until the 100x100 limit !!!!!!! (i wanted a straw hat shaped edge cut at…

Main components on the Ohara-75
Ohara-75 bill of materials (BOM)
40 components, 28 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | TP4056-42-ESOP8 | SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm_ThermalVias | U2 |
| 1 | AP2112K-3.3 | SOT-23-5 | U3 |
| 1 | Q_NMOS_GSD | SOT-23 | Q1 |
| 1 | Conn_01x24_Pin | Hirose_FH12-24S-0.5SH_1x24-1MP_P0.50mm_Horizontal | J1 |
| 1 | Micro_SD_Card_Det1 | microSD_XKB_XKTF-015-N | J2 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J3 |
| 1 | LiPo_3.7V | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J4 |
| 1 | Conn_01x06_Pin | PinHeader_1x06_P2.54mm_Vertical | J5 |
| 1 | Kailh_Choc_Next | SW_Kailh_Choc_v1 | SW1 |
| 1 | Kailh_Choc_Prev | SW_Kailh_Choc_v1 | SW2 |
| 1 | SW_RESET | SW_SPST_EVQP7A | SW3 |
| 1 | SW_BOOT | SW_SPST_EVQP7A | SW4 |
| 1 | POWER_SWITCH | SW_SPDT_Shouhan_MSK12C02 | SW10 |
| 1 | D_Schottky | D_SOD-123 | D1 |
| 1 | LED_DONE_GREEN | LED_0805_2012Metric | D2 |
| 1 | LED_CHRG_RED | LED_0805_2012Metric | D3 |
| 1 | 10uH | L_1210_3225Metric | L1 |
| 2 | 1uF | C_0805_2012Metric | C1, C5 |
| 6 | 4.7 uF | C_0805_2012Metric | C2, C3, C4, C6, C7, C8 |
Show 8 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 10uF | C_0805_2012Metric | C9 |
| 1 | C | C_0805_2012Metric | C10 |
| 2 | 10 uF | C_0805_2012Metric | C11, C12 |
| 4 | 10k | R_0805_2012Metric | R1, R3, R4, R5 |
| 1 | 1 ohm | R_0805_2012Metric | R2 |
| 2 | 5.1k | R_0805_2012Metric | R6, R7 |
| 1 | 1.2k | R_0805_2012Metric | R8 |
| 2 | R | R_0805_2012Metric | R9, R10 |
Ohara-75 design files
The KiCad project lives in the krishivjoshi219-collab/Ohara-75 repository on GitHub; these links point at the commit this page was built from.
- LayoutOhara-75.kicad_pcb
- SchematicOhara-75.kicad_sch
- BOMBOM.csv
Ohara-75: common questions
What microcontroller does the Ohara-75 use?
The Ohara-75 is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the Ohara-75 PCB?
The Ohara-75 measures 98 × 98 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Ohara-75?
40 components, from 28 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Ohara-75 design files?
From the krishivjoshi219-collab/Ohara-75 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Ohara-75 design in my own project?
The repository has no license, so all rights stay with krishivjoshi219-collab. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Ohara-75 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k