MeatLoaf-Hardware-ClausS
LeshanDaFo·MeatLoaf-Hardware-ClausS·Hardware/PCB-v1.0/KiCad/Meatloaf.kicad_pcb
About the MeatLoaf-Hardware-ClausS PCB
MeatLoaf-Hardware-ClausS is an open source ESP32 PCB design by LeshanDaFo, published on GitHub under the Custom license license. It is a 2-layer board measuring 63.7 × 73 mm, with 30 components from 15 distinct parts.
Its main chip is the ESP32-S3-DevKitC, from the ESP32 family. By type, the board carries 13 resistors, 7 transistors, 3 connectors, 3 diodes, 2 capacitors and 1 IC.
It belongs with the retro computing, dev boards & breakouts and iot & wireless designs in this gallery.
From the project
ESP32-S3 MeatLoaf hardware for Commodore C64/C128, including KiCad PCB designs, production files and firmware.
This document contains the assembly and connection information specific to carrier-board revision PCB v1.0. Do not apply these details to another PCB revision without checking its own documentation.
The carrier provides one common left-hand socket row and two alternative right-hand socket rows. It supports the following development-board layouts:
The firmware provided for PCB v1.0 uses the microSD-card slot on the carrier board. Although the Freenove ESP32-S3 WROOM Board has its own microSD-card slot, that slot is not enabled by this firmware. Insert the microSD card into the carrier-board…

Main components on the MeatLoaf-Hardware-ClausS
MeatLoaf-Hardware-ClausS bill of materials (BOM)
30 components, 15 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-DevKitC | ESP32-S3-DevKitC-1 | U1 |
| 5 | 2N7002 | SOT-23 | Q1, Q2, Q3, Q4, Q5 |
| 2 | MMBT3904 | SOT-23 | Q6, Q7 |
| 1 | 503398-1892 | MOLEX_503398-1892 | J1 |
| 2 | 0105 06 Commodore IEC Lumberg | Commodore_IEC | J2, J3 |
| 1 | ROOT | SW_Tactile_SPST_Angled_PTS645Vx58-2LFS | SW1 |
| 1 | Power | LED_D3.0mm | D1 |
| 1 | WiFi | LED_D3.0mm | D2 |
| 1 | BUS | LED_D3.0mm | D3 |
| 1 | 10uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1 |
| 1 | 100nF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2 |
| 6 | 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3, R4, R5, R10 |
| 2 | 4k7 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6, R8 |
| 2 | 100k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7, R9 |
| 3 | 470 | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R11, R12, R13 |
MeatLoaf-Hardware-ClausS design files
The KiCad project lives in the LeshanDaFo/MeatLoaf-Hardware-ClausS repository on GitHub; these links point at the commit this page was built from.
MeatLoaf-Hardware-ClausS: common questions
What microcontroller does the MeatLoaf-Hardware-ClausS use?
The MeatLoaf-Hardware-ClausS is built around the ESP32-S3-DevKitC, from the ESP32 family.
How big is the MeatLoaf-Hardware-ClausS PCB?
The MeatLoaf-Hardware-ClausS measures 63.7 × 73 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the MeatLoaf-Hardware-ClausS?
30 components, from 15 distinct parts. The full bill of materials is listed on this page.
Where can I download the MeatLoaf-Hardware-ClausS design files?
From the LeshanDaFo/MeatLoaf-Hardware-ClausS repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the MeatLoaf-Hardware-ClausS design in my own project?
It is published under Custom license, which limits how it may be reused; read the license before building on it.
Can I test firmware for the MeatLoaf-Hardware-ClausS without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k