Blue pill
lhondareyte·KiCad-Templates·STM32/bluepill/blue-pill.kicad_pcb
About the Blue pill PCB
Blue pill is an open source STM32 PCB design by lhondareyte, published on GitHub under the CC-BY-4.0 license. It is a 2-layer board, with 35 components from 21 distinct parts.
Its main chip is the STM32F103C8T6, from the STM32 family. Other key parts include the RT9193. By type, the board carries 15 capacitors, 9 resistors, 4 connectors, 2 ICs, 2 crystals and 2 diodes.
From the project
Generic Schematic KiCad Templates
Unfamous STM32 evaluation board based on STM32F103C8T6.
Main components on the Blue pill
Blue pill bill of materials (BOM)
35 components, 21 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | RT9193 | U1 | |
| 1 | STM32F103C8T6 | LQFP-48_7x7mm_P0.5mm | U2 |
| 1 | 8MHz | Y1 | |
| 1 | 32.768k | Y2 | |
| 1 | USB_B_Micro | J1 | |
| 1 | J-Link | J2 | |
| 1 | BOOTx | J3 | |
| 1 | Conn_02x20_Counter_Clockwise | J4 | |
| 1 | RST | SW1 | |
| 2 | LED | D1, D2 | |
| 7 | 10n | C1, C3, C4, C7, C8, C10, C11 | |
| 2 | 100n | C2, C5 | |
| 1 | 1u | C6 | |
| 4 | 20p | C9, C12, C13, C14 | |
| 1 | 2n2 | C15 | |
| 2 | 510R | R1, R5 | |
| 1 | 10k | R2 | |
| 2 | 100k | R3, R4 | |
| 1 | 1M | R6 | |
| 2 | 22R | R9, R11 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 1k5 | R10 |
Blue pill design files
The KiCad project lives in the lhondareyte/KiCad-Templates repository on GitHub; these links point at the commit this page was built from.
Blue pill: common questions
What microcontroller does the Blue pill use?
The Blue pill is built around the STM32F103C8T6, from the STM32 family.
How big is the Blue pill PCB?
The Blue pill has 2 copper layers and is 1.6 mm thick.
How many components are on the Blue pill?
35 components, from 21 distinct parts. The full bill of materials is listed on this page.
Where can I download the Blue pill design files?
From the lhondareyte/KiCad-Templates repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Blue pill design in my own project?
Yes, under the terms of its CC-BY-4.0 license, which lhondareyte chose for the repository.
Can I test firmware for the Blue pill without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in KiCad-Templates
- schematic only · 7 parts
Micro sd card
lhondareyte
7 parts2LCC-BY-4.01 - schematic only · 6 parts
Psu
lhondareyte
6 parts2LCC-BY-4.01 - schematic only · 6 partsAVR/Arduino
Arduino nano
lhondareyte
6 parts2LCC-BY-4.01 - schematic only · 6 partsAVR/Arduino
Atmega32u4
lhondareyte
6 parts2LCC-BY-4.01 - schematic only · 5 partsAVR/Arduino
Attiny2313
lhondareyte
5 parts2LCC-BY-4.01 Discovery-F4 base board
lhondareyte
53.3 × 30.5 mm4 parts2LCC-BY-4.01- schematic only · 4 partsAVR/Arduino
Atmega8
lhondareyte
4 parts2LCC-BY-4.01
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k