Pump
LokiMetaSmith·MR1·Pump/Pump.kicad_pcb
About the Pump PCB
Pump is an open source STM32 PCB design by LokiMetaSmith, published on GitHub under the AGPL-3.0 license. It is a 4-layer board measuring 88 × 88 mm, with 13 components from 11 distinct parts.
Its main chip is the STM32G431CBU6, from the STM32 family. Other key parts include the STUSB4500, TPS54302, LD39050_3V3, TS3USB221 and DRV8837C. By type, the board carries 9 ICs and 2 connectors.
From the project
The MR1 Nanopore Reader is an open-source, ultra-low-noise solid-state and biological nanopore sequencer flow cell, low-current transimpedance amplifier, and automated fluidic control system. It integrates high-precision parametric CAD models (build123d), ultra-low-leakage analog
The MR1 Nanopore Reader is an open-source, ultra-low-noise solid-state and biological nanopore sequencer flow cell, low-current transimpedance amplifier, and automated fluidic control system. It integrates high-precision parametric CAD models (build123d), ultra-low-leakage analog front-end electronics (KiCad), an automated dual-pump fluidic handler, and an ESP32-S3 high-speed continuous streaming firmware stack.
Main components on the Pump
Pump bill of materials (BOM)
13 components, 11 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32G431CBU6 | QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U1_MCU |
| 1 | STUSB4500 | QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U2_PD |
| 1 | TPS54302 | SOIC-8_3.9x4.9mm_P1.27mm | U3_BUCK |
| 1 | LD39050_3V3 | SOT-23-5 | U4_LDO |
| 1 | TS3USB221 | QFN-10_1.5x2mm_P0.4mm | U6_MUX |
| 2 | DRV8837C | WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mm | U7_DRV1, U8_DRV2 |
| 1 | ABP2_015PG_CIS | Honeywell_ABP_SMD | U9_SENS1 |
| 1 | ABP2_005PG_TRANS | Honeywell_ABP_SMD | U10_SENS2 |
| 1 | USB_C_HOST | USB_C_Receptacle_GCT_USB4085 | J1_HOST |
| 1 | USB_C_MR1_OUT | USB_C_Receptacle_GCT_USB4085 | J2_MR1 |
| 2 | PUMP_MOTOR | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J_PUMP1, J_PUMP2 |
Pump design files
The KiCad project lives in the LokiMetaSmith/MR1 repository on GitHub; these links point at the commit this page was built from.
- LayoutPump/Pump.kicad_pcb
- SchematicPump/Pump.kicad_sch
Pump: common questions
What microcontroller does the Pump use?
The Pump is built around the STM32G431CBU6, from the STM32 family.
How big is the Pump PCB?
The Pump measures 88 × 88 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Pump?
13 components, from 11 distinct parts. The full bill of materials is listed on this page.
Where can I download the Pump design files?
From the LokiMetaSmith/MR1 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Pump design in my own project?
Yes, under the terms of its AGPL-3.0 license, which LokiMetaSmith chose for the repository.
Can I test firmware for the Pump without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in MR1
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k