8 open source boards using the STUSB4500
Real designs built with the STUSB4500, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
OtterCastAmp
Ottercast
96 × 100 mm250 parts4LMIT341STM32
Led driver
Jana-Marie
41.6 × 32.6 mm112 parts4LCERN-OHL-S-2.08STM32
OtterStepMini
Jana-Marie
68.4 × 50 mm63 parts4LNo license5STM32
OPS
Jana-Marie
49 × 34 mm98 parts2LNo license3ESP32
Alaska-Deluxe-Generator
thehelmetedheinsight
75 × 55 mm54 parts2LGPL-3.00USB LED Daughterboard 0-2
Govish
63.5 × 25.4 mm61 parts2LMIT0STM32
Pump
LokiMetaSmith
88 × 88 mm13 parts4LAGPL-3.00STM32
Pump
EpicQuestBio
88 × 88 mm13 parts4LAGPL-3.00
How designs wire the STUSB4500
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the STUSB4500 connects to, and the resistors, capacitors and other passives placed on it.
- The VREG_1V2 pin has a capacitor to GND on 6 of 6 designs, most often 1 µF.
- The VREG_2V7 pin has a capacitor to GND on 6 of 6 designs, most often 1 µF.
- The RESET pin has a resistor to GND on 5 of 6 designs, most often 5.1 kΩ (then 100 kΩ).
- The ATTACH pin is left unconnected on 5 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| NCpin 3 | Connected to: Not connected 100% | — |
| RESETpin 6 | Connected to: Signal 83% · GND 17% |
|
| SCLpin 7 | Connected to: A connector 50%, the microcontroller 33% · not connected 17% |
|
| SDApin 8 | Connected to: A connector 50%, the microcontroller 33% · not connected 17% |
|
| DISCHpin 9 | Connected to: Not connected 50% · GND 17% · a signal 33% |
|
| GNDpin 10, 25 | Connected to: GND 100% | — |
| ATTACHpin 11 | Connected to: Not connected 83% · a signal 17% | — |
| ADDR0pin 12 | Connected to: GND 83% · a signal 17% | — |
| ADDR1pin 13 | Connected to: GND 83% · a signal 17% | — |
| POWER_OK3pin 14 | Connected to: Not connected 67% · a signal 33% | — |
| GPIOpin 15 | Connected to: Not connected 67% · a signal 33% | — |
| VBUS_EN_SNKpin 16 | Connected to: Not connected 50% · VBUS_SNK1 17% · a signal 33% |
|
| A_B_SIDEpin 17 | Connected to: Not connected 83% · a signal 17% | — |
| VBUS_VS_DISCHpin 18 | Connected to: Signal 100% |
|
| ALERTpin 19 | Connected to: Signal 67% · not connected 33% |
|
| POWER_OK2pin 20 | Connected to: Not connected 67% · a signal 33% | — |
| VREG_1V2pin 21 | Connected to: Signal 100% |
|
| VSYSpin 22 | Connected to: 3.3V 67% · GND 33% |
|
| VREG_2V7pin 23 | Connected to: Signal 100% |
|
| VDDpin 24 | Connected to: VBUS 50% · a signal 50% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include OtterCastAmp by Ottercast, Led driver by Jana-Marie, OtterStepMini by Jana-Marie and OPS by Jana-Marie.
The STUSB4500 in open source designs
The gallery holds 8 open source boards using the STUSB4500 from 8 GitHub repositories; a typical one measures about 71.7 × 52.5 mm and carries around 62 components.
63% use four copper layers or more, and 75% carry an open source license.
The most starred is OtterCastAmp by Ottercast.
Parts used alongside the STUSB4500
What boards using the STUSB4500 are built for
STUSB4500: common questions
Where can I find a STUSB4500 reference design?
Each of the 8 boards on this page is a real design using the STUSB4500. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the STUSB4500 VREG_1V2 pin connected?
The VREG_1V2 pin has a capacitor to GND on 6 of 6 designs, most often 1 µF. Counted from the KiCad layouts of 6 open source designs using the STUSB4500.
How is the STUSB4500 VREG_2V7 pin connected?
The VREG_2V7 pin has a capacitor to GND on 6 of 6 designs, most often 1 µF. Counted from the KiCad layouts of 6 open source designs using the STUSB4500.
What resistor goes on the STUSB4500 RESET pin?
The RESET pin has a resistor to GND on 5 of 6 designs, most often 5.1 kΩ (then 100 kΩ). Counted from the KiCad layouts of 6 open source designs using the STUSB4500.
What parts are used alongside the STUSB4500?
The ABP2_005PG_TRANS, ABP2_015PG_CIS, AP2204R-3.3, DRV8837C and LD39050_3V3 appear in the most repositories here.
Which microcontrollers do boards using the STUSB4500 use?
Most are built on STM32 (5) and ESP32 (1).
How big is a typical board using the STUSB4500?
The median is 71.7 × 52.5 mm, and 38% are two-layer designs.
What is the most popular open source board using the STUSB4500?
By GitHub stars, OtterCastAmp by Ottercast, with 341 stars.
Can I simulate one of these boards using the STUSB4500 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.