GW PCB Gerber
lonesoulsurfer·Thingtendo-Game-and-Watch-Clone·Kicad_Panel_Design/Kicad_PCB/Kicad_PCB/GW_PCB_Gerber.kicad_pcb
About the GW PCB Gerber
GW PCB Gerber is an open source ESP32 PCB design by lonesoulsurfer, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 120 × 55 mm, with 14 components from 13 distinct parts.
Its main chip is the ESP32-S3-ZERO, from the ESP32 family. Other key parts include the MAX98357A_Breakout and Boost_Charger_18x23.6. By type, the board carries 6 connectors, 3 ICs, 3 capacitors and 1 switch.
It belongs with the audio, power & battery and wearables designs in this gallery.
From the project
ESP32-S3 handheld that plays classic Game & Watch games. 2.4" colour screen, D-pad, speaker and battery.
A handheld that plays classic Nintendo Game & Watch games on an ESP32-S3, with a 2.4" colour screen, a D-pad, speaker and rechargeable battery.
This is a fork of slowlane112/Esp32-Game-and-Watch. All credit for the original firmware, emulator integration and hardware designs goes to that project. This fork adds a new hardware model, singlescreendpad, plus a few extra features.

Main components on the GW PCB Gerber
GW PCB Gerber bill of materials (BOM)
14 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-ZERO | MODULE_ESP32-S3-ZERO | U1 |
| 1 | MAX98357A_Breakout | MAX98357A_Breakout_1x07_P2.54mm | U2 |
| 1 | Boost_Charger_18x23.6 | Boost_Charger_18x23.6 | U3 |
| 1 | GP 15 | PinHeader_1x01_P1.00mm_Vertical | J1 |
| 1 | GP 14 | PinHeader_1x01_P1.00mm_Vertical | J2 |
| 1 | Conn_01x09_Pin | PinHeader_1x09_P2.54mm_Vertical_Oval | J3 |
| 1 | B+ | SolderWirePad_1x01_SMD_1x2mm | J4 |
| 1 | B- | SolderWirePad_1x01_SMD_1x2mm | J5 |
| 1 | 5V_Connector_testing | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J7 |
| 1 | SW_SPDT | SW_Slide-03_Wuerth-WS-SLTV_10x2.5x6.4_P2.54mm | SW8 |
| 1 | ST7789V | ST7789V_TFT_2.4 | TFT_Screen_2.4" |
| 2 | 100uf | CP_Radial_D5.0mm_P2.50mm | C6, C9 |
| 1 | 100nf | C_Disc_D4.3mm_W1.9mm_P5.00mm | C10 |
GW PCB Gerber design files
The KiCad project lives in the lonesoulsurfer/Thingtendo-Game-and-Watch-Clone repository on GitHub; these links point at the commit this page was built from.
GW PCB Gerber: common questions
What microcontroller does the GW PCB Gerber use?
The GW PCB Gerber is built around the ESP32-S3-ZERO, from the ESP32 family.
How big is the GW PCB Gerber?
The GW PCB Gerber measures 120 × 55 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the GW PCB Gerber?
14 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the GW PCB Gerber design files?
From the lonesoulsurfer/Thingtendo-Game-and-Watch-Clone repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the GW PCB Gerber design in my own project?
Yes, under the terms of its GPL-3.0 license, which lonesoulsurfer chose for the repository.
Can I test firmware for the GW PCB Gerber without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Thingtendo-Game-and-Watch-Clone
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k