11 open source boards using the ESP32-S3-ZERO

Real designs built with the ESP32-S3-ZERO, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

11 boardsClear filters|Most starred

How designs wire the ESP32-S3-ZERO

Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the ESP32-S3-ZERO connects to, and the resistors, capacitors and other passives placed on it.

  • The 5V_5V pin is tied to 5V on 4 of 5 designs.
  • The GPIO11 pin is left unconnected on 4 of 5 designs.
  • The GPIO12 pin is left unconnected on 4 of 6 designs (a signal on 2).
  • The 3V3(OUT)_3V3 pin is tied to 3.3V on 3 of 5 designs (not connected on 2).
3V3(OUT)_3V3pin 3V3Connected to: 3.3V 60% · not connected 40%
5V_5Vpin 5VConnected to: 5V 80% · a signal 20%
GPIO11pin 14Connected to: Not connected 80% · a signal 20%
GPIO12pin 15Connected to: Not connected 67% · a signal 33%
GPIO13pin 16Connected to: Not connected 60% · a signal 40%
TX_18pin 18Connected to: Not connected 60% · a signal 40%
GND_GNDpin GNDConnected to: GND 100%
RX_RXpin RXConnected to: Not connected 75% · a signal 25%
TX_TXpin TXConnected to: Not connected 75% · a signal 25%

14 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include GW PCB Gerber by lonesoulsurfer, Ondaire by rmalchow, TrailCurrentPlateau by trailcurrentoss and S3zero cc1101 by 13.

The ESP32-S3-ZERO in open source designs

The gallery holds 11 open source boards using the ESP32-S3-ZERO from 10 GitHub repositories; a typical one measures about 111.1 × 55 mm and carries around 16 components.

100% are two-layer designs, the rest use four layers or more, and 36% carry an open source license.

The most starred is Kicad - GW by lonesoulsurfer.

Microcontrollers on boards using the ESP32-S3-ZERO

ESP32-S3-ZERO: common questions

Where can I find a ESP32-S3-ZERO reference design?

Each of the 11 boards on this page is a real design using the ESP32-S3-ZERO. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the ESP32-S3-ZERO 5V_5V pin connected?

The 5V_5V pin is tied to 5V on 4 of 5 designs. Counted from the KiCad layouts of 9 open source designs using the ESP32-S3-ZERO.

How is the ESP32-S3-ZERO GPIO11 pin connected?

The GPIO11 pin is left unconnected on 4 of 5 designs. Counted from the KiCad layouts of 9 open source designs using the ESP32-S3-ZERO.

How is the ESP32-S3-ZERO GPIO12 pin connected?

The GPIO12 pin is left unconnected on 4 of 6 designs (a signal on 2). Counted from the KiCad layouts of 9 open source designs using the ESP32-S3-ZERO.

Which microcontrollers do boards using the ESP32-S3-ZERO use?

Most are built on ESP32 (11).

How big is a typical board using the ESP32-S3-ZERO?

The median is 111.1 × 55 mm, and 100% are two-layer designs.

What is the most popular open source board using the ESP32-S3-ZERO?

By GitHub stars, Kicad - GW by lonesoulsurfer, with 5 stars.

Can I simulate one of these boards using the ESP32-S3-ZERO before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part