Kicad - GW
lonesoulsurfer·Thingtendo-Game-and-Watch-Clone·Kicad_GW/Kicad - GW.kicad_pcb
About the Kicad - GW PCB
Kicad - GW is an open source ESP32 PCB design by lonesoulsurfer, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 120 × 55 mm, with 23 components from 22 distinct parts.
Its main chip is the ESP32-S3-ZERO, from the ESP32 family. Other key parts include the MAX98357A_Breakout and Boost_Charger_18x23.6. By type, the board carries 9 switches, 7 connectors, 3 ICs and 3 capacitors.
It belongs with the audio, power & battery and wearables designs in this gallery.
From the project
ESP32-S3 handheld that plays classic Game & Watch games. 2.4" colour screen, D-pad, speaker and battery.
A handheld that plays classic Nintendo Game & Watch games on an ESP32-S3, with a 2.4" colour screen, a D-pad, speaker and rechargeable battery.
This is a fork of slowlane112/Esp32-Game-and-Watch. All credit for the original firmware, emulator integration and hardware designs goes to that project. This fork adds a new hardware model, singlescreendpad, plus a few extra features.

Main components on the Kicad - GW
Kicad - GW bill of materials (BOM)
23 components, 22 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-ZERO | MODULE_ESP32-S3-ZERO | U1 |
| 1 | MAX98357A_Breakout | MAX98357A_Breakout_1x07_P2.54mm | U2 |
| 1 | Boost_Charger_18x23.6 | Boost_Charger_18x23.6 | U3 |
| 1 | GP 15 | PinHeader_1x01_P1.00mm_Vertical | J1 |
| 1 | GP 14 | PinHeader_1x01_P1.00mm_Vertical | J2 |
| 1 | Conn_01x09_Pin | PinHeader_1x09_P2.54mm_Vertical_Oval | J3 |
| 1 | B+ | SolderWirePad_1x01_SMD_1x2mm | J4 |
| 1 | B- | SolderWirePad_1x01_SMD_1x2mm | J5 |
| 1 | Conn_01x09_Pin | PinHeader_1x09_P2.54mm_Vertical | J6 |
| 1 | 5V_Connector_testing | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J7 |
| 1 | left | SW_SKRGAED010 | SW1 |
| 1 | right | SW_SKRGAED010 | SW2 |
| 1 | up | SW_SKRGAED010 | SW3 |
| 1 | down | SW_SKRGAED010 | SW4 |
| 1 | jump | SW_SKRGAED010 | SW5 |
| 1 | B | SW_Tactile_3x6x2.5 | SW6 |
| 1 | time | SW_Tactile_3x6x2.5 | SW7 |
| 1 | SW_SPDT | SW_Slide-03_Wuerth-WS-SLTV_10x2.5x6.4_P2.54mm | SW8 |
| 1 | A | SW_Tactile_3x6x2.5 | SW10 |
| 1 | ST7789V | ST7789V_TFT_2.4 | TFT_Screen_2.4" |
Show 2 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 100uf | CP_Radial_D5.0mm_P2.50mm | C6, C9 |
| 1 | 100nf | C_Disc_D4.3mm_W1.9mm_P5.00mm | C10 |
Kicad - GW design files
The KiCad project lives in the lonesoulsurfer/Thingtendo-Game-and-Watch-Clone repository on GitHub; these links point at the commit this page was built from.
- LayoutKicad_GW/Kicad - GW.kicad_pcb
- SchematicKicad_GW/Kicad - GW.kicad_sch
Kicad - GW: common questions
What microcontroller does the Kicad - GW use?
The Kicad - GW is built around the ESP32-S3-ZERO, from the ESP32 family.
How big is the Kicad - GW PCB?
The Kicad - GW measures 120 × 55 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Kicad - GW?
23 components, from 22 distinct parts. The full bill of materials is listed on this page.
Where can I download the Kicad - GW design files?
From the lonesoulsurfer/Thingtendo-Game-and-Watch-Clone repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Kicad - GW design in my own project?
Yes, under the terms of its GPL-3.0 license, which lonesoulsurfer chose for the repository.
Can I test firmware for the Kicad - GW without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Thingtendo-Game-and-Watch-Clone
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k