Slider
About the Slider PCB
Slider is an open source AVR/Arduino PCB design by lucanastasio, published on GitHub. It is a 2-layer board measuring 44 × 39 mm, with 35 components from 18 distinct parts.
Its main chip is the ATtiny13A-S, from the AVR/Arduino family. Other key parts include the LM358, L78L05_SOT89 and ATtiny13A-SS. By type, the board carries 14 capacitors, 6 resistors, 4 ICs, 3 diodes, 2 transistors and 2 connectors.
From the project
Home automation stuff
- Dimmer: LED APA102-2020, 4 PWM ch. - Central: 4 PWM ch., radar UART, air valve 4 pin
Main components on the Slider
Slider bill of materials (BOM)
35 components, 18 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM358 | SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | L78L05_SOT89 | SOT-89-3 | U2 |
| 1 | ATtiny13A-S | SOIC-8W_5.3x5.3mm_P1.27mm | U3 |
| 1 | ATtiny13A-SS | SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 2 | AO3400A | SOT-23W_Handsoldering | Q1, Q2 |
| 1 | AVR-ISP-6 | PinHeader_2x03_P2.54mm_Vertical | J4 |
| 1 | Screw_Terminal_01x04 | PhoenixContact_MCV_1,5_4-G-3.81_1x04_P3.81mm_Vertical | J8 |
| 1 | Fuse | Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1 |
| 2 | R_Potentiometer | Alpha_RA2043F-20 | RV1, RV2 |
| 1 | SW_Push_LED | SW_PUSH-12mm_LED | SW1 |
| 1 | LED | LED_D5.0mm_Clear | D1 |
| 2 | D_Zener | Nexperia_CFP3_SOD-123W | D2, D3 |
| 11 | C | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C3, C4, C5, C7, C8, C11 +3 |
| 2 | C_Polarized | CP_Elec_6.3x5.4 | C6, C9 |
| 1 | C_Polarized | CP_Elec_8x6.7 | C10 |
| 4 | R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3, R5 |
| 1 | R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
| 1 | R_Pack04_Split | R_Array_Convex_4x0603 | RN1 |
Slider design files
The KiCad project lives in the lucanastasio/myHomeAutomation repository on GitHub; these links point at the commit this page was built from.
Slider: common questions
What microcontroller does the Slider use?
The Slider is built around the ATtiny13A-S, from the AVR/Arduino family.
How big is the Slider PCB?
The Slider measures 44 × 39 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Slider?
35 components, from 18 distinct parts. The full bill of materials is listed on this page.
Where can I download the Slider design files?
From the lucanastasio/myHomeAutomation repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Slider design in my own project?
The repository has no license, so all rights stay with lucanastasio. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Slider without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in myHomeAutomation
AVR/ArduinoControl panel
65 × 58 mm158 parts2LNo license1
AVR/ArduinoSwing
50 × 50 mm146 parts4LNo license1
AVR/ArduinoHeating controller
100 × 50 mm145 parts2LNo license1
AVR/ArduinoRoom hub
50 × 50 mm121 parts2LNo license1
Led balance
100 × 60 mm94 parts2LNo license1
Corridor distribution
60 × 100 mm81 parts2LNo license1
ADV7280-M
50 × 36 mm77 parts4LNo license1
Knob top 30
25 × 25 mm65 parts2LNo license1
Corridor node
40 × 40 mm57 parts2LNo license1
AVR/ArduinoGeneric node
48.9 × 17.8 mm47 parts4LNo license1
Repeater
55 × 35 mm41 parts2LNo license1
Similar boards
AVR/ArduinoRedox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0k
AVR/ArduinoModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoV4
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoDiscipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k
AVR/ArduinoMegadesk
gcormier
41.7 × 32.2 mm23 parts2LGPL-3.0818
AVR/ArduinoEasyduino Atmega Nano
Hanqaqa
43.4 × 18 mm30 parts4LCERN-OHL-P-2.0746