Esp32-c3-dev board
marouane-daoudi·esp32-c3-dev-board·kicad/ESP32_C3_Mini.kicad_pcb
About the Esp32-c3-dev board
Esp32-c3-dev board is an open source ESP32 PCB design by marouane-daoudi, published on GitHub. It is a 4-layer board measuring 32.6 × 40 mm, with 31 components from 18 distinct parts.
Its main chip is the ESP32-C3-WROOM-02, from the ESP32 family. Other key parts include the USBLC6-2P6 and AP2112K-3.3. By type, the board carries 10 capacitors, 10 resistors, 3 ICs, 3 connectors, 2 switches and 2 diodes.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
4-layer ESP32-C3 WROOM development board with USB-C, ESD protection, LDO regulation and differential pair routing — designed in KiCad
A 4-layer development and testing board for the ESP32-C3-WROOM-02 module. It uses USB-C for 5V input and USB 2.0 data, includes onboard 3.3V LDO regulation, ESD protection on the USB data and VBUS lines, an external crystal, reset and boot buttons, a 3.3V power indicator LED, and breadboard-compatible GPIO headers.
The board was designed in KiCad 10.0 with a focus on power integrity, signal routing, ESD return paths, and low-impedance power distribution.

Main components on the Esp32-c3-dev board
Esp32-c3-dev board bill of materials (BOM)
31 components, 18 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | USBLC6-2P6 | SOT-666 | U1 |
| 1 | AP2112K-3.3 | SOT-23-5_HandSoldering | U2 |
| 1 | ESP32-C3-WROOM-02 | ESP32-C3-WROOM-02 | U3 |
| 1 | Crystal | Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J1 |
| 2 | Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J2, J3 |
| 2 | SW_Push | SW_SPST_B3U-1000P | SW1, SW2 |
| 1 | PESD5V0L1UL | D_SOD-882 | D1 |
| 1 | GREEN | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |
| 5 | 4u7 | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C3, C4, C5 |
| 3 | 100nf | C_0402_1005Metric | C6, C9, C10 |
| 2 | 12.5pF | C_0201_0603Metric_Pad0.64x0.40mm_HandSolder | C7, C8 |
| 2 | 5.1K | R_0402_1005Metric | R1, R2 |
| 1 | R | R_0805_2012Metric | R3 |
| 1 | TBD | R_0201_0603Metric | R4 |
| 4 | 10K | R_0402_1005Metric | R5, R7, R8, R9 |
| 1 | 100 | R_0402_1005Metric | R6 |
| 1 | 1K | R_0402_1005Metric | R10 |
Esp32-c3-dev board design files
The KiCad project lives in the marouane-daoudi/esp32-c3-dev-board repository on GitHub; these links point at the commit this page was built from.
- Layoutkicad/ESP32_C3_Mini.kicad_pcb
- Schematickicad/ESP32_C3_Mini.kicad_sch
Esp32-c3-dev board: common questions
What microcontroller does the Esp32-c3-dev board use?
The Esp32-c3-dev board is built around the ESP32-C3-WROOM-02, from the ESP32 family.
How big is the Esp32-c3-dev board?
The Esp32-c3-dev board measures 32.6 × 40 mm, has 4 copper layers and is 1 mm thick.
How many components are on the Esp32-c3-dev board?
31 components, from 18 distinct parts. The full bill of materials is listed on this page.
Where can I download the Esp32-c3-dev board design files?
From the marouane-daoudi/esp32-c3-dev-board repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Esp32-c3-dev board design in my own project?
The repository has no license, so all rights stay with marouane-daoudi. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Esp32-c3-dev board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k