OpenESPTemp
mawaeg·OpenESPTemp·electronics/OpenESPTemp.kicad_pcb
About the OpenESPTemp PCB
OpenESPTemp is an open source ESP32 PCB design by mawaeg, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 15 × 63 mm, with 34 components from 22 distinct parts.
Its main chip is the ESP32-C6-MINI-1/U, from the ESP32 family. Other key parts include the RV-3028-C7, BME280 and TLV70033_SOT23-5. By type, the board carries 11 capacitors, 11 resistors, 4 ICs, 4 switches, 2 transistors and 1 connector.
It belongs with the sensors, iot & wireless and power & battery designs in this gallery.
From the project
An open-source, battery-powered temperature and environmental monitoring sensor.
OpenESPTemp is an open-source, battery-powered temperature and environmental monitoring sensor built using an ESP32-C6 and a BME280 sensor. It is designed for integration into IoT systems.
The PCB is designed to operate with a rechargeable LiFePo4 AA battery. This repository includes the PCB design, a 3D-printable case, and basic firmware.
- Temperature Monitoring: Provides readings using the BME280 sensor. - Environmental Sensing: Includes humidity and pressure measurements. - Low Power: Optimized for battery-powered operation (under 200nA power consumption while sleeping). - Battery…

Main components on the OpenESPTemp
OpenESPTemp bill of materials (BOM)
34 components, 22 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | RV-3028-C7 RV-3028-C7 32.768kHz 1ppm TA QC | MicroCrystal_C7_SON-8_1.5x3.2mm_P0.9mm | U2 |
| 1 | BME280 BME280 | Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumbering | U3 |
| 1 | TLV70033_SOT23-5 TLV70033_SOT23-5 | SOT-23-5 | U4 |
| 1 | ESP32-C6-MINI-1/U ESP32-C6-MINI-1-N4 | ESP32-C6-MINI-1 | U5 |
| 1 | TSM260P02CX-RFG TSM260P02CX RFG | SOT-23 | Q1 |
| 1 | DMN2020LSN-7 DMN2020LSN-7 | SOT-23 | Q2 |
| 1 | Qwiic_RA SM04B-SRSS-TB(LF)(SN) | JST_1x04_P1.0mm_Horizontal_SMD | J2 |
| 1 | Battery 53 | Keystone_53_Dual | BT1 |
| 1 | WAKE B3U-1000P | SW_SPST_B3U-1000P | SW1 |
| 1 | FCT B3U-1000P | SW_SPST_B3U-1000P | SW2 |
| 1 | BOOT B3U-1000P | SW_SPST_B3U-1000P | SW3 |
| 1 | RESET B3U-1000P | SW_SPST_B3U-1000P | SW4 |
| 1 | 22u GRM188R61A226ME15D | C_0603_1608Metric | C1 |
| 6 | 0.1u CL10B104KB8NNNC | C_0603_1608Metric | C2, C4, C5, C6, C7, C10 |
| 1 | 10u CL10A106MQ8NNNC | C_0603_1608Metric | C3 |
| 1 | 10n CL10B103KB8NNNC | C_0603_1608Metric | C8 |
| 1 | 1u CL10A105KB8NNNC | C_0603_1608Metric | C9 |
| 1 | 2.2u CL10A225KO8NNNC | C_0603_1608Metric | C11 |
| 5 | 10k MCT06030C1002FPW00 | R_0603_1608Metric | R1, R2, R3, R4, R7 |
| 2 | 4.7k MCT06030C4701FP500 | R_0603_1608Metric | R5, R6 |
Show 2 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | 100k MCT06030C1003FP500 | R_0603_1608Metric | R8, R10, R11 |
| 1 | 1M CRCW06031M00FKEA | R_0603_1608Metric | R9 |
OpenESPTemp design files
The KiCad project lives in the mawaeg/OpenESPTemp repository on GitHub; these links point at the commit this page was built from.
OpenESPTemp: common questions
What microcontroller does the OpenESPTemp use?
The OpenESPTemp is built around the ESP32-C6-MINI-1/U, from the ESP32 family.
How big is the OpenESPTemp PCB?
The OpenESPTemp measures 15 × 63 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the OpenESPTemp?
34 components, from 22 distinct parts. The full bill of materials is listed on this page.
Where can I download the OpenESPTemp design files?
From the mawaeg/OpenESPTemp repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the OpenESPTemp design in my own project?
Yes, under the terms of its GPL-3.0 license, which mawaeg chose for the repository.
Can I test firmware for the OpenESPTemp without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k