21 open source boards using the RV-3028-C7
Real designs built with the RV-3028-C7, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
V5 main
zynthian
245.2 × 100 mm144 parts2LNo license156ESP32
NX-ISD
Ghost3379
77 × 48.6 mm108 parts4LGPL-3.02ESP32
Dpf load monitor wide
v-cu
50 × 23 mm106 parts6LCC-BY-NC-4.01Microchip SAM
Samd51 gps alarm clock
KrHaaland
80 × 50 mm149 parts2LNo license0ESP32
Alec main
eshelton328
64 × 56 mm112 parts4LNo license0ESP32
Alec main
eshelton328
64 × 56 mm112 parts4LNo license0Raspberry Pi
Laser nephelometer
sai-ydev
56.6 × 57.7 mm103 parts2LGPL-3.00AVR/Arduino
BinaryClock
kwame-y
60 × 30 mm52 parts4LNo license0ESP32
Goofy ahh epaper watch
haohaohaoyan
66 × 36 mm50 parts2LNo license0Microchip SAM
MoodLogger v1
sullyjason
30 × 30 mm48 parts2LNo license0ESP32
OpenESPTemp
mawaeg
15 × 63 mm34 parts2LGPL-3.00Microsensor board
BeeEyeIoT
27 × 26 mm20 parts4LNo license0- schematic only · 61 partsESP32
JWatch
JujuXu
61 partsNo license0 Raspberry Pi
Inki
c0de111
47.2 × 55.5 mm54 parts2LApache-2.039Microchip SAM
GNSS Alarm Clock
KrHaaland
80 × 50 mm146 parts4LNo license0ESP32
Esp32s3-devkit-5v
eshelton328
64 × 56 mm112 parts4LNo license0ESP32
Esp32s3-devkit-5v
eshelton328
64 × 56 mm112 parts4LNo license0ESP32
Zone syntax test
gokcesena53
90 × 55 mm89 parts4LMIT0STM32
Lighthouse Base
mwuerms
90 × 66.3 mm45 parts4LMIT0ESP32
Alec sensor
eshelton328
64 × 56 mm88 parts4LNo license0ESP32
Alec sensor
eshelton328
64 × 56 mm88 parts4LNo license0
How designs wire the RV-3028-C7
Read from the KiCad layouts of 14 open source designs, one per repository: what each pin of the RV-3028-C7 connects to, and the resistors, capacitors and other passives placed on it.
- The SCL_3 pin has a pull-up to 3.3V on 12 of 14 designs, most often 4.7 kΩ (then 10 kΩ).
- The SDA_4 pin has a pull-up to 3.3V on 12 of 14 designs, most often 4.7 kΩ (then 10 kΩ).
- The VDD_7 pin has a decoupling capacitor on 12 of 14 designs, most often 100 nF (then 10 µF).
- The CLKOUT_1 pin is left unconnected on 11 of 14 designs (a signal on 3).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CLKOUT_1pin 1 | Connected to: Not connected 79% · a signal 21% | — |
| INT_2pin 2 | Connected to: The microcontroller 43% · not connected 29% |
|
| SCL_3pin 3 | Connected to: The microcontroller 71% |
|
| SDA_4pin 4 | Connected to: The microcontroller 71% |
|
| VSS_5pin 5 | Connected to: GND 100% | — |
| VBACKUP_6pin 6 | Connected to: Signal 79% |
|
| VDD_7pin 7 | Connected to: 3.3V 93% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include V5 main by zynthian, Inki by c0de111, NX-ISD by Ghost3379 and Dpf load monitor wide by v-cu.
The RV-3028-C7 in open source designs
The gallery holds 21 open source boards using the RV-3028-C7 from 16 GitHub repositories; a typical one measures about 64 × 55.8 mm and carries around 89 components.
65% use four copper layers or more, and 29% carry an open source license.
The most starred is V5 main by zynthian.
Parts used alongside the RV-3028-C7
Microcontrollers on boards using the RV-3028-C7
What boards using the RV-3028-C7 are built for
RV-3028-C7: common questions
Where can I find a RV-3028-C7 reference design?
Each of the 21 boards on this page is a real design using the RV-3028-C7. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the RV-3028-C7 SCL_3 pin?
The SCL_3 pin has a pull-up to 3.3V on 12 of 14 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 14 open source designs using the RV-3028-C7.
What pull-up resistor is used on the RV-3028-C7 SDA_4 pin?
The SDA_4 pin has a pull-up to 3.3V on 12 of 14 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 14 open source designs using the RV-3028-C7.
What decoupling capacitors do designs use on the RV-3028-C7 VDD_7 pin?
The VDD_7 pin has a decoupling capacitor on 12 of 14 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 14 open source designs using the RV-3028-C7.
What parts are used alongside the RV-3028-C7?
The USBLC6-2SC6, DS3231M, ESP32-S3-WROOM-1-N16, MAX98357A and PCA9306 appear in the most repositories here.
Which microcontrollers do boards using the RV-3028-C7 use?
Most are built on ESP32 (12), Microchip SAM (3), Raspberry Pi (2) and AVR/Arduino (1).
How big is a typical board using the RV-3028-C7?
The median is 64 × 55.8 mm, and 35% are two-layer designs.
What is the most popular open source board using the RV-3028-C7?
By GitHub stars, V5 main by zynthian, with 156 stars.
Can I simulate one of these boards using the RV-3028-C7 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.