Controle

mbouyer·domotique·hardware/controle/controle.kicad_pcb

Controle PCB layout, top view — open source PIC board by mbouyer

About the Controle PCB

Controle is an open source PIC PCB design by mbouyer, published on GitHub under the BSD-3-Clause license. It is a 2-layer board measuring 83.6 × 76.7 mm, with 81 components from 46 distinct parts.

Its main chip is the PIC18F05Q40, from the PIC family. Other key parts include the ULN2003, MCP7940N-xSN, MCP2003B, TPS54228 and NCP718xSN330. By type, the board carries 31 resistors, 16 capacitors, 12 connectors, 7 diodes, 6 ICs and 4 transistors.

From the project

gestion du chauffage et aération d'une habitation

Main components on the Controle

Controle bill of materials (BOM)

81 components, 46 distinct parts.

QtyPartRefs
1
ULN2003
U1
1
MCP7940N-xSN
U2
1
MCP2003B
U3
1
TPS54228
U4
1
NCP718xSN330
U5
1
PIC18F05Q40
U6
2
DMG2307L
Q1, Q2
2
BSS123
Q3, Q4
1
32.768Khz
Y1
1
TWI3
J1
1
SENS0375
J2
1
TWI4
J3
1
LED
J4
1
UART7
J5
1
PWR
J6
1
DATA
J7
1
Serial
J8
1
Barrel_Jack
J9
1
Conn_01x05_Pin
J10
1
ADC
J11
Show 26 more
QtyPartRefs
1
PWM
J12
1
5V_LIME2
+5V1
1
CR2032
BT1
1
FL40YA-V36P-2X20-LF
GPIO-1
2
LED_ABRG
D1, D2
3
RED
D3, D5, D6
1
S1M
D4
1
RED
D7
1
4.7µH
L1
4
100nF
C1, C8, C16, C17
3
10pF
C2, C3, C11
1
1µF
C4
1
220pF
C5
1
10µF25V
C7
1
6.8nF
C9
1
1µF6.3v
C10
2
22µF6.3V
C12, C13
2
4.7µ
C14, C15
7
1K
R1, R2, R6, R11, R12, R14, R17
6
4.7K
R3, R4, R9, R10, R18, R19
7
330
R5, R7, R8, R13, R15, R16, R28
2
2.2K
R20, R21
3
47K
R22, R23, R26
1
56K
R25
4
10K
R27, R29, R30, R32
1
SNS-LDR5MM
R31

Controle design files

The KiCad project lives in the mbouyer/domotique repository on GitHub; these links point at the commit this page was built from.

Controle: common questions

What microcontroller does the Controle use?

The Controle is built around the PIC18F05Q40, from the PIC family.

How big is the Controle PCB?

The Controle measures 83.6 × 76.7 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Controle?

81 components, from 46 distinct parts. The full bill of materials is listed on this page.

Where can I download the Controle design files?

From the mbouyer/domotique repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Controle design in my own project?

Yes, under the terms of its BSD-3-Clause license, which mbouyer chose for the repository.

Can I test firmware for the Controle without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.

More boards in domotique

Similar boards