Ventil
mbouyer·domotique·hardware/ventil/ventil.kicad_pcb
About the Ventil PCB
Ventil is an open source PIC PCB design by mbouyer, published on GitHub under the BSD-3-Clause license. It is a 2-layer board measuring 60 × 42 mm, with 28 components from 21 distinct parts.
Its main chip is the PIC18F05Q40, from the PIC family. Other key parts include the SHT31-DIS, MCP2003B, uA7805 and ULN2003. By type, the board carries 8 capacitors, 8 resistors, 5 ICs, 4 connectors, 2 diodes and 1 transistor.
From the project
gestion du chauffage et aération d'une habitation
Main components on the Ventil
Ventil bill of materials (BOM)
28 components, 21 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SHT31-DIS | Sensirion_DFN-8-1EP_2.5x2.5mm_P0.5mm_EP1.1x1.7mm | U1 |
| 1 | PIC18F05Q40 | SOIC-14_3.9x8.7mm_P1.27mm | U2 |
| 1 | MCP2003B | SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | uA7805 | TO-252-3_TabPin2 | U5 |
| 1 | ULN2003 | SOIC-16_3.9x9.9mm_P1.27mm | U6 |
| 1 | BSS123 | SOT-23 | Q1 |
| 1 | Conn_01x05_Pin | Molex_Pico-SPOX-5-Vertical | J1 |
| 1 | M | JST_XH_S5B-XH-A_1x05_P2.50mm_Horizontal | J2 |
| 1 | BUS | Molex Pico-SPOX-4_90 | J3 |
| 1 | i2C | Molex Pico-SPOX-4_90 | J4 |
| 1 | LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | SMBJ16A | D_SMB_Handsoldering | D2 |
| 4 | 100nF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C3, C5 |
| 1 | 1µF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C6 |
| 1 | 220pF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C7 |
| 1 | 10uF | C_1210_3225Metric_Pad1.33x2.70mm_HandSolder | C8 |
| 1 | 10uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C9 |
| 2 | 10K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R6 |
| 4 | 4.7K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R3, R13, R14 |
| 1 | 330 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 47K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7 |
Ventil design files
The KiCad project lives in the mbouyer/domotique repository on GitHub; these links point at the commit this page was built from.
Ventil: common questions
What microcontroller does the Ventil use?
The Ventil is built around the PIC18F05Q40, from the PIC family.
How big is the Ventil PCB?
The Ventil measures 60 × 42 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Ventil?
28 components, from 21 distinct parts. The full bill of materials is listed on this page.
Where can I download the Ventil design files?
From the mbouyer/domotique repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Ventil design in my own project?
Yes, under the terms of its BSD-3-Clause license, which mbouyer chose for the repository.
Can I test firmware for the Ventil without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.
More boards in domotique
PIC
Energie
mbouyer
103 × 87 mm91 parts2LBSD-3-Clause0PIC
Controle
mbouyer
83.6 × 76.7 mm81 parts2LBSD-3-Clause0PIC
Vmc
mbouyer
63 × 29 mm36 parts2LBSD-3-Clause0Rsr232-iso
mbouyer
51 × 23 mm14 parts2LBSD-3-Clause0Linky serial
mbouyer
42.2 × 10.9 mm8 parts2LBSD-3-Clause0Sht31-break
mbouyer
24.9 × 15.9 mm3 parts2LBSD-3-Clause0
Similar boards
PIC
Pslab hardware
fossasia
99 × 53.3 mm187 parts4LApache-2.01.7kPIC
Lens
ervanalb
80 × 80 mm53 parts4LNo license515PIC
Micro 8088
skiselev
152.4 × 101.6 mm71 partsGPL-3.0414PIC
GB-CARTPP-DIY
Gekkio
100 × 100 mm22 parts2LCC-BY-4.0379PIC
GB-LIVE32
Gekkio
51.4 × 61 mm46 parts4LCC-BY-4.0379PIC
GB-CART256K-A
Gekkio
51.4 × 61 mm17 parts2LCC-BY-4.0379