23 open source boards using the SHT31-DIS

Real designs built with the SHT31-DIS, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

23 boardsClear filters|Most starred

How designs wire the SHT31-DIS

Read from the KiCad layouts of 18 open source designs, one per repository: what each pin of the SHT31-DIS connects to, and the resistors, capacitors and other passives placed on it.

  • The SCL pin has a pull-up to 3.3V on 14 of 18 designs, most often 10 kΩ (then 4.7 kΩ).
  • The ALERT pin is left unconnected on 16 of 18 designs (a signal on 2).
  • The RESET pin is left unconnected on 16 of 18 designs (a signal on 2).
  • The SDA pin has a pull-up to 3.3V on 13 of 18 designs, most often 10 kΩ (then 4.7 kΩ).
SDApin 1Connected to: A connector 33%, the microcontroller 33%
  • Pull-up to 3.3V on 72% · 10 kΩ (11), 4.7 kΩ (5), 2.2 kΩ (2)
ADDRpin 2Connected to: GND 72% · a signal 22%
ALERTpin 3Connected to: Not connected 89%
SCLpin 4Connected to: A connector 33%, the microcontroller 33%
  • Pull-up to 3.3V on 78% · 10 kΩ (11), 4.7 kΩ (6), 2.2 kΩ (2)
VDDpin 5Connected to: 3.3V 83%
  • Decoupling capacitor on 72% · 100 nF (17), 2.2 µF (1), 1 µF (1)
RESETpin 6Connected to: Not connected 89%
Rpin 7Connected to: GND 82%
VSSpin 8, 9Connected to: GND 94%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Smartdisplay hardware by BearLaboratory, BATDATUNIT01 by mlab-modules, Particle bamf23-badge by particle-iot and Flipper thermal camera by Badbird5907.

The SHT31-DIS in open source designs

The gallery holds 23 open source boards using the SHT31-DIS from 21 GitHub repositories; a typical one measures about 63 × 56 mm and carries around 37 components.

100% are two-layer designs, the rest use four layers or more, and 43% carry an open source license.

The most starred is Smartdisplay hardware by BearLaboratory.

Microcontrollers on boards using the SHT31-DIS

SHT31-DIS: common questions

Where can I find a SHT31-DIS reference design?

Each of the 23 boards on this page is a real design using the SHT31-DIS. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the SHT31-DIS SCL pin?

The SCL pin has a pull-up to 3.3V on 14 of 18 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 18 open source designs using the SHT31-DIS.

How is the SHT31-DIS ALERT pin connected?

The ALERT pin is left unconnected on 16 of 18 designs (a signal on 2). Counted from the KiCad layouts of 18 open source designs using the SHT31-DIS.

How is the SHT31-DIS RESET pin connected?

The RESET pin is left unconnected on 16 of 18 designs (a signal on 2). Counted from the KiCad layouts of 18 open source designs using the SHT31-DIS.

What parts are used alongside the SHT31-DIS?

The AMS1117-3.3, AP2112K-3.3, APDS-9960, AT24CS64-SSHM and BH1750FVI-TR appear in the most repositories here.

Which microcontrollers do boards using the SHT31-DIS use?

Most are built on ESP32 (7), ESP8266 (2), PIC (2) and STM32 (2).

How big is a typical board using the SHT31-DIS?

The median is 63 × 56 mm, and 100% are two-layer designs.

What is the most popular open source board using the SHT31-DIS?

By GitHub stars, Smartdisplay hardware by BearLaboratory, with 175 stars.

Can I simulate one of these boards using the SHT31-DIS before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part