Spikey watch v2
meowchao·spikey-watch-v2·spikey-watch-v2/spikey-watch-v2.kicad_pcb
About the Spikey watch v2 PCB
Spikey watch v2 is an open source ESP32 PCB design by meowchao, published on GitHub. It is a 2-layer board measuring 48 × 33 mm, with 44 components from 20 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the USBLC6-2SC6, AP2112K-3.3, TP4056 and BMA400. By type, the board carries 12 capacitors, 11 resistors, 7 diodes, 5 ICs, 4 switches and 2 connectors.
It belongs with the wearables designs in this gallery.
From the project
- [x] Schematic Complete - [x] PCB Routing - [ ] PCB Manufactured - [ ] Bring-up - [ ] Firmware Development - [ ] Deep Sleep Optimization
Main components on the Spikey watch v2
Spikey watch v2 bill of materials (BOM)
44 components, 20 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U2 |
| 1 | AP2112K-3.3 | SOT-23-5 | U3 |
| 1 | TP4056 | SOT-23-5 | U4 |
| 1 | BMA400 | LGA-12_2x2mm_P0.5mm | U5 |
| 1 | FDN340P | SOT-23 | Q1 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | Conn_01x02_Pin | Molex_Micro-Latch_53253-0270_1x02_P2.00mm_Vertical | J2 |
| 2 | SW_SPST | SW_SPST_B3U-1000P | RESET1, boot1 |
| 4 | USER_SW | Panasonic_EVQPUL_EVQPUC | SW3, SW4, SW7, SW8 |
| 2 | ESD9B3.3ST5G | D_SOD-923 | D1, D2 |
| 1 | MBR0530 | D_SOD-123 | D3 |
| 4 | ESD3.3 | D_SOD-923 | D6, D7, D10, D11 |
| 2 | 100u | C_0603_1608Metric | C1, C4 |
| 1 | 10u | C_0603_1608Metric | C2 |
| 7 | 100n | C_0603_1608Metric | C3, C7, C8, C9, C10, C13, C14 |
| 2 | 1uF | C_0603_1608Metric | C5, C6 |
| 7 | 10K | R_0603_1608Metric | R1, R4, R7, R8, R9, R12, R13 |
| 3 | 5.1K | R_0603_1608Metric | R2, R3, R5 |
| 1 | 100K | R_0603_1608Metric | R6 |
Spikey watch v2 design files
The KiCad project lives in the meowchao/spikey-watch-v2 repository on GitHub; these links point at the commit this page was built from.
Spikey watch v2: common questions
What microcontroller does the Spikey watch v2 use?
The Spikey watch v2 is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the Spikey watch v2 PCB?
The Spikey watch v2 measures 48 × 33 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Spikey watch v2?
44 components, from 20 distinct parts. The full bill of materials is listed on this page.
Where can I download the Spikey watch v2 design files?
From the meowchao/spikey-watch-v2 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Spikey watch v2 design in my own project?
The repository has no license, so all rights stay with meowchao. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Spikey watch v2 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k