Self balancing robot
MostafaMokhtar8545·self-balancing-robot·PCB/Board V2/self balance robot V2.kicad_pcb
About the Self balancing robot PCB
Self balancing robot is an open source ESP32 PCB design by MostafaMokhtar8545, published on GitHub. It is a 2-layer board measuring 52.1 × 78.4 mm, with 21 components from 16 distinct parts.
Its main chip is the ESP32_DevKit_V1_DOIT_30GPIOs, from the ESP32 family. Other key parts include the ESP32-DEVKITC-32D and Pololu_Breakout_A4988. By type, the board carries 10 connectors, 3 modules, 3 capacitors, 2 ICs, 2 resistors and 1 switch.
It belongs with the robotics & motion designs in this gallery.
Main components on the Self balancing robot
Self balancing robot bill of materials (BOM)
21 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-DEVKITC-32D | MODULE_ESP32-DEVKITC-32D | U1 |
| 1 | ~ | mini360 | U2 |
| 2 | Pololu_Breakout_A4988 | Pololu_Breakout-16_15.2x20.3mm | A1, A2 |
| 1 | ESP32_DevKit_V1_DOIT_30GPIOs | DOIT_ESP32_DEVKIT_30Pins | A3 |
| 1 | PINHD_1x19_Female | PinSocket_1x19_P2.54mm_Vertical | J1 |
| 2 | PINHD_1x4_Male | PinHeader_1x04_P2.54mm_Vertical | J2, J4 |
| 1 | PINHD_1x8_Female | PinSocket_1x08_P2.54mm_Vertical | J3 |
| 1 | PINHD_1x6_Male | PinHeader_1x06_P2.54mm_Vertical | J5 |
| 2 | PINHD_1x3_Male | PinHeader_1x03_P2.54mm_Vertical | J6, J7 |
| 2 | PINHD_2x4_Male | PinHeader_2x04_P2.54mm_Vertical | J8, J9 |
| 1 | Screw_Terminal_2_P3.50mm | TerminalBlock_Phoenix_PT-1,5-2-3.5-H_1x02_P3.50mm_Horizontal | J10 |
| 1 | SW_Wuerth_450301014042 | SW_Slide-03_Wuerth-WS-SLTV_10x2.5x6.4_P2.54mm | SW1 |
| 2 | 100u | CP_Radial_D5.0mm_P2.50mm | C1, C4 |
| 1 | 470u | CP_Radial_D5.0mm_P2.50mm | C3 |
| 1 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3 |
| 1 | 2.4k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R4 |
Self balancing robot design files
The KiCad project lives in the MostafaMokhtar8545/self-balancing-robot repository on GitHub; these links point at the commit this page was built from.
Self balancing robot: common questions
What microcontroller does the Self balancing robot use?
The Self balancing robot is built around the ESP32_DevKit_V1_DOIT_30GPIOs, from the ESP32 family.
How big is the Self balancing robot PCB?
The Self balancing robot measures 52.1 × 78.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Self balancing robot?
21 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the Self balancing robot design files?
From the MostafaMokhtar8545/self-balancing-robot repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Self balancing robot design in my own project?
The repository has no license, so all rights stay with MostafaMokhtar8545. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Self balancing robot without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k