Dexterbie
mrdexterssj·dexterbie·dexterbie/_restore_backup_2026-10-09T23-21-17-522/dexterbie.kicad_pcb
About the Dexterbie PCB
Dexterbie is an open source ESP32 PCB design by mrdexterssj, published on GitHub. It is a 2-layer board measuring 68.5 × 13.8 mm, with 7 components from 6 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 2 ICs, 2 connectors, 2 switches and 1 resistor.
It belongs with the displays & leds designs in this gallery.
From the project
The Half-Life week 1 starter project with some tweaks by me! A tiny motion-controlled digital pet, basically a desktop Tamagotchi. Totally not a Starboy.
Dexterbie is a small tamagotchi-like device! It gives you a friend that sits in your desk during long coding hours. It has 2 buttons, the left one opens the menu and the right one opens the stats menu. It comes with a motion sensor and an environmental sensor, so you can interact physically with your virtual friend!
Dexterbie is designed to just sit on your desk and do silly stuff to keep you company. You can interact with it in many ways: by tilting it or through the 2 built-in buttons!

Main components on the Dexterbie
Dexterbie bill of materials (BOM)
7 components, 6 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C3-SMD | U1 |
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U2 |
| 1 | Conn_01x04_Pin | Display_128x64_096_I2C | J1 |
| 1 | Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J2 |
| 2 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2 |
| 1 | 10k | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
Dexterbie design files
The KiCad project lives in the mrdexterssj/dexterbie repository on GitHub; these links point at the commit this page was built from.
Dexterbie: common questions
What microcontroller does the Dexterbie use?
The Dexterbie is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Dexterbie PCB?
The Dexterbie measures 68.5 × 13.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Dexterbie?
7 components, from 6 distinct parts. The full bill of materials is listed on this page.
Where can I download the Dexterbie design files?
From the mrdexterssj/dexterbie repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Dexterbie design in my own project?
The repository has no license, so all rights stay with mrdexterssj. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Dexterbie without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k