Io can
nealpalmer·io_can·iocan_rev1_schematic_layout/io_can_rev1.kicad_pcb
About the Io can PCB
Io can is an open source ESP32 PCB design by nealpalmer, published on GitHub. It is a 2-layer board measuring 39 × 29 mm, with 47 components from 22 distinct parts.
Its main chip is the XIAO-ESP32-S3-DIP, from the ESP32 family. Other key parts include the PIC16F1778-xSS, TPS54202DDC, TCAN857-Q1 and AP74700QW6-7. By type, the board carries 16 capacitors, 11 resistors, 5 ICs, 5 diodes, 4 connectors and 2 transistors.
It belongs with the displays & leds designs in this gallery.
From the project
FRC CAN device for general purpose IO - open source/schematic/pcb
This is a circuit boards to plug into the FRC can bus, and give you 4 GPIO pins for use in software. This should help reduce the complexity of wiring, by putting the GPIO near the device. There is probably already CAN and power near where the sensor would need to be.
Neal Palmer, FRC team #2984 Vikings Robotics, La Jolla, CA, USA
Main components on the Io can
Io can bill of materials (BOM)
47 components, 22 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | PIC16F1778-xSS | SSOP-28_5.3x10.2mm_P0.65mm | U1 |
| 1 | TPS54202DDC | SOT-23-6 | U2 |
| 1 | TCAN857-Q1 | TSOT-23-8_HandSoldering | U3 |
| 1 | AP74700QW6-7 | SOT-23-6_Handsoldering | U4 |
| 1 | XIAO-ESP32-S3-DIP | XIAO-ESP32S3-DIP | U5 |
| 1 | AO3401A | SOT-23 | Q1 |
| 1 | DMG2302U | SOT-23 | Q2 |
| 4 | CDR-04-TR | CDR-04-TR | J1, J2, J3, J4 |
| 2 | 2A Polyfuse | Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1, F2 |
| 1 | PTS526SK15SMTR2 LFS | SW_Tactile_SPST_NO_Straight_CK_PTS636Sx25SMTRLFS | SW1 |
| 3 | 1734/NeoPixel_THT | LED_D5.0mm-4_RGB_Staggered_Pins | D1, D2, D3 |
| 1 | MBR230S1F-7 (2A Schottky) | D_SOD-123F | D4 |
| 1 | NUP2105L | SOT-23 | D5 |
| 1 | 220nH 2520 | L_1008_2520Metric_Pad1.43x2.20mm_HandSolder | L1 |
| 8 | 1uF 0603 | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C6, C7, C8, C15, C16, C17 |
| 5 | 1uF 0603 25V | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4, C5, C9, C13, C14 |
| 1 | 10uF 0603 25V | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C10 |
| 2 | 22uF 0603 10V | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C11, C12 |
| 5 | 10K 0603 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R4, R5, R7 |
| 1 | 1.37K 0603 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
Show 2 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 5K 0603 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6 |
| 4 | 500R 0603 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R8, R9, R10, R11 |
Io can design files
The KiCad project lives in the nealpalmer/io_can repository on GitHub; these links point at the commit this page was built from.
Io can: common questions
What microcontroller does the Io can use?
The Io can is built around the XIAO-ESP32-S3-DIP, from the ESP32 family.
How big is the Io can PCB?
The Io can measures 39 × 29 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Io can?
47 components, from 22 distinct parts. The full bill of materials is listed on this page.
Where can I download the Io can design files?
From the nealpalmer/io_can repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Io can design in my own project?
The repository has no license, so all rights stay with nealpalmer. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Io can without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k